manualshive.com logo in svg

Cisco PIX 520, Руководство пользователя, Страница: 3 / 24

Поделиться
Скачать
Cisco PIX 520 Скачать руководство пользователя страница 3

5-3

Cisco PIX Security Appliance Hardware Installation Guide

78-15170-02

Chapter 5      PIX 520

PIX 520 Product Overview

Figure 5-3

 shows the location of the interfaces if you install a four-port Ethernet circuit board in slot 0.

Figure 5-3

Four-Port Ethernet Circuit Board Installed in Slot 0

Figure 5-4

 shows how the slots are numbered if a single-port Ethernet circuit board is inserted in

slot 0, and a four-port Ethernet circuit board is inserted in slot 1.

Figure 5-4

Single-Port Ethernet Circuit Board Installed in Slot 0 and Four-Port Ethernet Circuit Board 
Installed in Slot 1

Figure 5-5

 shows how the slots are numbered if single-port Ethernet circuit boards are installed in slot 0 

and in slot 1, and a four-port Ethernet circuit board is inserted in slot 2.

Figure 5-5

Single-Port Ethernet Circuit Board Installed in Slot 0 and 1 and Four-Port Ethernet Circuit 
Board Installed in Slot 2

44306

Interface 5

Interface 4

Interface 0
Interface 1
Interface 2
Interface 3

44307

Interface 0

Interface 1

Interface 2
Interface 3
Interface 4

44308

Interface 0

Interface 1

Interface 3
Interface 4

Interface 2

Interface 5

Содержание PIX 520

























Отзывы:

Нет отзывов