Cisco o UCS X440p Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 62

background image

What to do next

Reinsert an FHFL GPU. See

Installing a FHFL GPU, on page 29

.

Installing a FHFL GPU

Type A riser cages have two alignment pins for the single PCIe connector. The pair of pins catches a pair of
notches on the GPU bracket to correctly position the GPU.

Use the following procedure to install a full height full length GPU into a Type A riser.

Before you begin

Review the

GPU Replacement Guidelines and Limitations, on page 26

Step 1

Plug the black connector of GPU auxiliary (AUX) power cable into the FHFL GPU.

Step 2

Attach the GPU to the Type A riser.

a) Orient the GPU so that the notches on the GPU bracket line up with the pins on the riser cage.

You might need to open the riser door completely to have enough space to insert the FHFL GPU.

Note

b) Lower the FHFL GPU so that the front edge will slide into the lowest retaining bracket on the riser cage floor.
c) Align the GPU connector with its socket on the riser.
d) Gently slide the GPU along the floor of the riser, making sure that the bottom notch on the retaining bracket captures

the FHFL.

Make sure that the GPU power cable does not obstruct the GPU. Do not allow the cable to get pinched or
exceed a reasonable bend radius.

Caution

Cisco UCS X440p PCIe Node Installation and Service Guide

29

Servicing the Cisco UCS X440p PCIe Node

Installing a FHFL GPU

«
...
35
36
37
38
39
...
»

Содержание o UCS X440p































































Отзывы:

Нет отзывов

Похожие инструкции для o UCS X440p

System x3630 M4

Бренд: IBM Страницы: 7

Бренд: Abocom Страницы: 11

Бренд: Abocom Страницы: 19

Бренд: H3C Страницы: 34

Бренд: Palm Страницы: 4

VigorIPPBX 2820 Series

Бренд: Draytek Страницы: 29

Бренд: ETAS Страницы: 69

Бренд: WHOOP Страницы: 26

Бренд: ZyXEL Communications Страницы: 125

SteelCentral NetExpress

Бренд: Riverbed Страницы: 38

AyrMesh IndoorAP

Бренд: AYRSTONE Страницы: 2

Easy Tool-ID BSG TID-05-T30-00-005

Бренд: Balluff Страницы: 46

memonizerWORKSTATION

Бренд: MEMON Страницы: 2

18x18 Card Cage

Бренд: WolfPack Страницы: 31

Converter Board R0E521237CFK00

Бренд: Renesas Страницы: 6

Бренд: Aewin Technologies Страницы: 86

Бренд: Ubiquiti Страницы: 20

Бренд: Altera Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды