manualshive.com logo in svg

Cisco Nexus 2000 Series, Руководство по установке

Поделиться
Скачать
Cisco Nexus 2000 Series Скачать руководство пользователя страница 155

B-1

Cisco Nexus 2000 Series Hardware Installation Guide

 

A P P E N D I X

 

B

Technical Specifications

This appendix describes the technical specifications for the Cisco Nexus Fabric Extenders (FEXs) and 
includes the following sections:

•

Power Specifications, page B-1

•

Environmental Specifications, page B-6

•

Physical Specifications, page B-6

•

Transceiver Specifications, page B-7

•

Airflow Optimization Accessories, page B-9

Note

Specifications for cables and connectors are provided in 

Appendix C, “Cable and Port Specifications.”

Power Specifications

This section describes the power specifications for the Cisco Nexus Fabric Extenders.

The power supplies connect directly to the system through connectors attached to the baseboard through 
cables. One connector is on the baseboard for each power supply. AC input is through an IEC connector 
mounted on the power supply port side exhaust panel. 

Table B-1

 lists the specifications for the FEX 

power supplies.

Содержание Nexus 2000 Series































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды