manualshive.com logo in svg

Cisco NCS 6000 Series, Руководство по настройке, Страница: 176 / 498

Поделиться
Скачать
Cisco NCS 6000 Series Скачать руководство пользователя страница 176

Configuring BFD Session Teardown Based on Echo Latency Detection

You can configure BFD sessions on non-bundle interfaces to bring down a BFD session when it exceeds the
configured echo latency tolerance.

To configure BFD session teardown using echo latency detection, complete the following steps.

Before you enable echo latency detection, be sure that your BFD configuration supports echo mode.

Echo latency detection is not supported on bundle interfaces.

DETAILED STEPS

SUMMARY STEPS

1.

configure

2.

bfd

3.

echo latency detect

[

percentage percent-value

[

count packet-count

]

4.

commit

DETAILED STEPS

Purpose

Command or Action

configure

Step 1

Enters BFD configuration mode.

bfd

Example:

Step 2

RP/0/RP0/CPU0:router(config)# bfd

Enables echo packet latency detection over the course of a
BFD session, where:

echo latency detect

[

percentage percent-value

[

count

packet-count

]

Step 3

Example:

•

percentage percent-value

—Specifies the percentage

of the echo failure detection time to be detected as bad
latency. The range is 100 to 250. The default is 100.

RP/0/RP0/CPU0:router(config-bfd)# echo latency
detect

•

count packet-count

—Specifies a number of

consecutive packets received with bad latency that will
take down a BFD session. The range is 1 to 10. The
default is 1.

commit

Step 4

Delaying BFD Session Startup Until Verification of Echo Path and Latency

You can verify that the echo packet path is working and within configured latency thresholds before starting
a BFD session on non-bundle interfaces.

Echo startup validation is not supported on bundle interfaces.

Note

Routing Configuration Guide for Cisco NCS 6000 Series Routers, IOS XR Release 6.4.x

154

Implementing BFD

Configuring BFD Session Teardown Based on Echo Latency Detection

Содержание NCS 6000 Series



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов