Cisco NCS 5501 Скачать руководство пользователя страница 7

Страница: 7 / 82

Preface

•

Changes to This Document, page vii

•

Obtaining Documentation and Submitting a Service Request, page vii

Changes to This Document

This table lists the technical changes made to this document since it was first released.

Table 1: Changes to This Document

Summary

Date

Initial release of the cumulative hardware document covering NCS 5500 Series
Fixed-Port Routers from 6.3.1 release onwards.

Fixed-port routers include the NCS 5501, NCS 5501 SE, NCS 5502, NCS 5502
SE, NCS 55A1-24H, and NCS 55A1-36H.

Information for the NCS 5500 Series Modular Routers (NCS 5504, NCS
5508, and NCS 5516) can be found in the

Hardware Installation Guide

for Cisco NCS 5500 Series Modular Routers

Note

August 2017

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service
request, and gathering additional information, see

What's New in Cisco Product Documentation

To receive new and revised Cisco technical content directly to your desktop, you can subscribe to the

What's

New in Cisco Product Documentation RSS feed

. RSS feeds are a free service.

Hardware Installation Guide for Cisco NCS 5500 Series Fixed-Port Routers

vii

Содержание NCS 5501



















































































Результаты поиска

Содержание NCS 5501

Отзывы:

Бренды по названию

Популярные бренды

Cisco NCS 5501, Руководство по установке оборудования

Результаты поиска

Содержание NCS 5501

Отзывы:

Бренды по названию

Популярные бренды