Cisco NCS 2000 series Скачать руководство пользователя страница 473 | Manualshive

Страница: 473 / 602

background image

When you replace a card an identical card, you do not need to make any changes to the database.

Note

If the troubleshooting procedure does not clear the alarm, log into the Technical Support Website at

http://www.cisco.com/

c/en/us/support/index.html

or call the Cisco Technical Assistance Center (1 800 553-2447) to report the problem.

UNQUAL-PPM

Default Severity: Not Reported (NR), Non-Service-Affecting (NSA)

Logical Objects: PPM

The Unqualified PPM Inserted condition occurs when a PPM with a nonqualified product ID is plugged into
the card port; that is, the PPM passes the security code check as a Cisco PPM but is not qualified for use on
the particular card.

Clear the UNQUAL-PPM Condition

SUMMARY STEPS

1.

Obtain the correct Cisco PPM and replace the existing PPM with the new one.

DETAILED STEPS

Obtain the correct Cisco PPM and replace the existing PPM with the new one.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

UNREACHABLE-TARGET-POWER

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Logical Object: OCH

The Unreachable Port Target Power alarm occurs on WSS32 cards during startup as the card laser attains its
correct power level. The condition disappears when the card successfully boots.

Card power levels are listed in the

Hardware Specifications

document.

Note

UNREACHABLE-TARGET-POWER is an informational condition. It only requires troubleshooting if it
does not clear.

Note

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

427

Alarm Troubleshooting

UNQUAL-PPM

«
...
471
472
473
474
475
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: ABB Страницы: 66

Бренд: Maco Страницы: 38

UP Squared 6000 Edge Computing Kit

Бренд: Aaeon Страницы: 59

Бренд: Zonet Страницы: 10

Бренд: Samsung Страницы: 65

Бренд: Commell Страницы: 36

Бренд: National Instruments Страницы: 9

Бренд: Conceptronic Страницы: 230

iW-RainboW-G30D

Бренд: iWave Страницы: 89

Бренд: Vivotek Страницы: 170

Бренд: insys icom Страницы: 4

Бренд: Ubiquiti Страницы: 20

Бренд: Talent Страницы: 18

Бренд: ZyXEL Communications Страницы: 2

ipRocketLink IAD 3086

Бренд: Patton electronics Страницы: 12

Бренд: Fluke Страницы: 102

Бренд: Omron Страницы: 432

Бренд: Ciara Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды