Cisco NCS 2000 series Скачать руководство пользователя страница 349 | Manualshive

Страница: 349 / 602

background image

DETAILED STEPS

Complete the

Replace the Alarm Interface Panel, on page 461

procedure.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

MEA (PPM)

Default Severity: Critical (CR), Service-Affecting (SA)

Logical Object: PPM

The Missing Equipment Attributes alarm for the PPM (SFP) is raised on TXP, MXP, MRC-12 and
OC192-XFP/STM-64-XP cards when the PPM (SFP) is misprovisioned or unsupported. It can occur when
you provision the PPM (SFP) for a wavelength that is explicitly not the first tunable wavelength.

When the TNCS-2 card is replacing the TNC card pre-provisioned with OC3 payload on a chassis, the
PROV-MISMATCH/MEA alarm is raised. Delete the pre-provisioning on the TNCS-2 card to proceed.

Note

Clear the MEA (PPM) Alarm

SUMMARY STEPS

1.

To provision the PPM (SFP), you must first create it in CTC. To do this, complete the following steps:

2.

After you have created the PPM (SFP), or if you see it listed in the Pluggable Port Modules area but not
in the Selected PPM area, choose the port rate:

3.

If you see the port listed in the Pluggable Port Modules area and the Selected PPM area, the MEA indicates
that the incorrect port rate was selected. Click the port in the Selected PPM area and click Delete.

4.

Complete

Step 2, on page 304

to correctly provision the port rate.

DETAILED STEPS

Step 1

To provision the PPM (SFP), you must first create it in CTC. To do this, complete the following steps:

a) In node view (single-shelf mode) or shelf view (multishelf mode), double-click the reporting card to open the card

view.

b) Click the

Provisioning

>

Pluggable Port Modules

tabs. (If you already see the PPM [SFP] listed in the Pluggable

Port Modules Area, go to

Step 2, on page 304

.)

c) Under the Pluggable Port Modules area, click

Create

.

d) In the Create PPM dialog box, choose the card PPM (SFP) number from the drop-down list (for example, PPM 1).
e) Choose the PPM (SFP) type from the second drop-down list, for example PPM (1 Port).

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

303

Alarm Troubleshooting

MEA (PPM)

«
...
347
348
349
350
351
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: National Instruments Страницы: 5

Бренд: National Instruments Страницы: 76

Бренд: National Instruments Страницы: 34

Бренд: Paradyne Страницы: 2

Бренд: Paradyne Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: Zhone Страницы: 2

Бренд: Telex Communications Страницы: 28

USB-BRIDGEV2-EVAL

Бренд: IDT Страницы: 11

Бренд: Juniper Страницы: 825

Бренд: OpenVox Страницы: 13

Бренд: HELVAR Страницы: 2

HHM Series HHM2245SA1

Бренд: TDK Страницы: 2

Бренд: Cervoz Страницы: 22

Quadro M6000 Sync

Бренд: Nvidia Страницы: 8

SiliconDrive SSD-P16G(I)-3100

Бренд: Silicon Systems Страницы: 108

Бренд: CNC4PC Страницы: 11

Бренд: VCS Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды