Cisco NCS 2000 series Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 602

background image

alarm can be raised against the optical signal (OC-N) or the optical transport layer overhead (OTN) as well
as other objects. Therefore, both OCN: LOS and OTN: LOS appear in the list (as well as the other objects).

Alarm profile list objects are defined in

Table 11: Alarm Logical Object Type Definitions, on page 110

Alarm logical object names can appear as abbreviated versions of standard terms used in the system and the
documentation. For example, the OCN logical object refers to the OC-N signal. Logical object names or
industry-standard terms are used within the entries as appropriate.

Note

Alarm Logical Objects

The table below lists all logical alarm objects used in this chapter.

Table 11: Alarm Logical Object Type Definitions

Definition

Logical Object

Reshape and retransmit (used for transponder [TXP] cards).

2R

Alarm Interface ControllerInternational/alarm expansion panel. A combination term that
refers to this platform AIC-I card.

AICI-AEP

Alarm Interface Controller-International/Alarm Interface Extension. A combination term
that refers to this platform's AIC-I card.

AICI-AIE

Alarm Interface Panel.

AIP

Amplified optical transport section.

AOTS

Building integrated timing supply incoming references (BITS-1, BITS-2).

BITS

The backplane.

BPLANE

An environmental alarm port.

ENVALRM

A card, its physical objects, and its logical objects as they are located in any of the eight
noncommon card slots. The EQPT object is used for alarms that refer to the card itself
and all other objects on the card including ports, lines, synchronous transport signals
(STS), and virtual tributaries (VT).

EQPT

Enterprise System Connection fiber optic technology, referring to the following TXP
cards: TXP_MR_2.5G, TXPP_MR_2.5G, MXP_MR_2.5G, MXPP_MR_2.5G, AR-XP,
AR-MXP, AR-XPE.

ESCON

BITS outgoing references (SYNC-BITS1, SYNC-BITS2).

EXT-SREF

Fan-tray assembly.

FAN

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

110

Alarm Troubleshooting

Alarm Logical Objects

«
...
154
155
156
157
158
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Univerge SV8100

Бренд: NEC Страницы: 44

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 2

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 28

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 2

Бренд: DataRemote Страницы: 2

Бренд: Salusfin Страницы: 6

Бренд: TFortis Страницы: 86

Бренд: MiLAN Страницы: 1

PacketShaper PS-S200

Бренд: Symantec Страницы: 2

Бренд: SIIG Страницы: 12

Бренд: VCS Страницы: 118

Бренд: protech Страницы: 95

Hotwire ATM Line Cards 8335

Бренд: Paradyne Страницы: 132

ISDN SOHO Router

Бренд: AOpen Страницы: 89

Husky HMG-1648EP

Бренд: Ethernet Direct Страницы: 16

Бренд: OPTO 22 Страницы: 28

Бренд: ATI Technologies Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды