Cisco N9K-C93180YC-FX Скачать руководство пользователя страница 59

Страница: 59 / 74

Power Specifications

Power specifications include the specifications for each type of power supply module.

500-W AC Power Supply Specifications

These specifications apply to the following power supplies:

• NXA-PAC-500W-PE

• NXA-PAC-500W-PI

Specification

Characteristic

Nominal range: 100 and 240 VAC (Range: 90-132
VAC, 180-264 VAC)

AC input voltage

Nominal range: 50 to 60 Hz (Range: 47-63 Hz)

AC input frequency

7.6 A at 100 VAC

3.65 A at 208 VAC

Maximum AC input current

760 A at 100 VAC

Maximum input volt-amperes

500 W

Maximum output power per power supply

33 A (sub-cycle duration)

Maximum inrush current

12 ms at 500 W

Maximum hold-up time

12 VDC

Power supply output voltage

12 VDC

Power supply standby voltage

Climate Savers Platinum Efficiency (80Plus Platinum
certified)

Efficiency rating

RSP1

Form factor

1200-W HVAC/HVDC Power Supply Specifications

These specifications apply to the 1200-W HVAC/HVDC (N9K-PUV-1200W) power supplies.

Specification

Characteristic

Nominal (Range)

• 200 to 277 VAC

• –240 to –380 VDC

Input voltage

• AC (for 1230 W output)

• DC (for 1230 W output)

Nominal: 50 to 60 Hz (Range: 47-63 Hz)

AC input frequency

Cisco Nexus 93180YC-FX ACI-Mode Switch Hardware Installation Guide

System Specifications

Power Specifications

Содержание N9K-C93180YC-FX











































































Результаты поиска

Содержание N9K-C93180YC-FX

Отзывы:

Бренды по названию

Популярные бренды

Cisco N9K-C93180YC-FX, Установка оборудования

Результаты поиска

Содержание N9K-C93180YC-FX

Отзывы:

Бренды по названию

Популярные бренды