Cisco Meraki MR84 Скачать руководство пользователя страница 12

This equipment complies with FCC radiation exposure limits set forth for an 
uncontrolled environment. This equipment should be installed and operated 
with minimum distance 27.5 cm between the radiator and your body. This 
transmitter must not be co-located or operating in conjunction with any 

other antenna or transmitter.  

IEEE 802.11b or 802.11g operation of this product in the USA is firmware-

limited to channels 1 through 11.  

If the device is going to be operated in the 5.15 - 5.25 frequency range, 
then it is restricted to indoor environment only. This device meets all other 
requirements specified in Part 15E, Section 15.407 of the FCC Rules.  

Industry Canada Statement  

This device complies with RSS-247 of the Industry Canada Rules. Operation 
is subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference 

received, including interference that may cause undesired operation.  

Ce dispositif est conforme à la norme CNR-247 d’Industrie Canada 

applicable aux appareils radio exempts de licence. Son fonctionnement est 
sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de 
brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage 
reçu, y compris un brouillage susceptible de provoquer un fonctionnement 

indésirable.  

Industry Canada Caution  

(i) the device for operation in the band 5150-5250 MHz is only for indoor 
use to reduce the potential for harmful interference to co-channel mobile 
satellite systems;  

(ii) high-power radars are allocated as primary users (i.e. priority users) of 

the bands 5250-5350 MHz and 5650-5850 MHz and that these radars 
could cause interference and/or damage to LE-LAN devices.  

Avertissement:  

(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés 
uniquement pour une utilisation à l’intérieur afin de réduire les risques de 
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les 

mêmes canaux;  

(ii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de 
radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., 

qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz 
et que ces  

radars pourraient causer du brouillage et/ou des dommages aux dispositifs 

Содержание Meraki MR84














Отзывы: