Cisco Meraki MR55-HW Скачать руководство пользователя страница 26

 

If the  device  is  going  to be  operated  in  the  5.15 - 5.25  frequency  range,  then it  is  restricted  to 

indoor environment  only.

 

This device meets all other requirements specified in Part 15E, Section 15.407 of the FCC 
Rules.

 

 

Industry Canada Statement

 

This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the 

following two conditions:

 

(1)

 

This device may not cause harmful interference, and (2) this device must accept any 

interference received, including  interference that may cause undesired operation.

 

 

Ce dispositif est conforme à la norme CNR-247 

d’Industrie

 Canada applicable aux appareils radio 

exempts de licence.

 

Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas 

produire de brouillage

 

préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage 

susceptible de provoquer un fonctionnement indésirable.

 

 

Industry Canada Caution

 

(i)

 

the device for operation in the band 5150-5250 MHz is only for indoor use to reduce 

the potential for harmful  interference to co-channel mobile satellite systems;

 

 

(ii)

 

high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 

MHz and 5650-5850 MHz  and that these radars could cause interference and/or damage to LE-
LAN devices.

 

 

Avertissement:

 

(i)

 

les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour 

une utilisation à 

l’intérieur

  afin de réduire les risques de brouillage préjudiciable aux systèmes de 

satellites mobiles utilisant les mêmes canaux;

 

 

(ii)

 

De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute 

puissance sont désignés  utilisateurs principaux (c.-à-d., 

qu’ils

 ont la priorité) pour les bandes 5 

250-5 350 MHz et 5 650-5 850 MHz et que ces

 

radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

 

 

Industry Canada Radiation Exposure Statement

 

This equipment complies with IC radiation exposure limits set forth for an uncontrolled 

environment. This equipment should be installed and operated with minimum distance 38 cm between 
the radiator & your body.

 

 

Déclaration 

d’exposition

  aux  radiations

 

Cet équipement est conforme aux limites 

d’exposition

 aux rayonnements IC établies pour un 

environnement non con  trôlé. Cet équipement doit être installé et utilisé avec un minimum de 38 
cm de distance entre la source de rayonnement  et votre corps.

 

 
 

 

Copyright

 

© 2015 Cisco Systems, Inc. All rights 
reserved. Trademarks

 

 

 

Содержание Meraki MR55-HW




























Отзывы: