Cisco MDS 9500 Series Скачать руководство пользователя страница 51

Страница: 51 / 66

Shared Interfaces

Any change in protocol state that flaps the parent port of a shared interface because of any port feature
also affects the FCOE traffic on the storage vdc.

Note

The following interface config modes are not allowed while sharing an interface from Ethernet vdc to a storage
vdc:

•

SPAN destination

•

Private VLAN mode

•

Port-channel interfaces

•

Access mode

•

mac-packet-classify

•

Interfaces that are part of a VLAN that has an associated QoS policy

Shared Ethernet interfaces must be in trunk mode and only shared with one other VDC.

Storage VDC

Configuring a VDC for the OOB management interface mgmt0 is accomplished with the

vrf context

management

command. However, a storage VDC does not support VRF, so configuring mgmt0 requires a

different approach.

The following table shows how to configure mgmt 0 for a VDC and for a storage VDC:

Configuring mgmt 0 for storage VDC

Configuring mgmt 0 for VDC

interface mgmt 0
ip address

mgmt0_ip_address mgmt0_subnet_mask

no shut
ip route 0.0.0.0/0

default_gateway

The

ip route

command specifies the default

route that points to the default gateway.

Note

vrf context management
ip route 0.0.0.0/0

default_gateway

where

•

mgmt0_ip_address

is the mgmt0 IPv4 address.

•

mgmt0_subnet_mask

is the mgmt0 IPv4 netmask.

•

default_gateway

is the IPv4 address of the default-gateway.

For more information about VDC, see the

Cisco Nexus 7000 Series NX-OS Virtual Device Context Configuration

Guide

Cisco MDS 9500: Guidelines and Limitations

•

You cannot enable FCoE on the default VLAN.

•

You can only enable FCoE on an FCoE module.

Cisco NX-OS FCoE Configuration Guide for Nexus 7000 and MDS 9500

OL-25809-02

Storage VDC on Cisco Nexus 7000 Series Switches

Cisco MDS 9500: Guidelines and Limitations

Содержание MDS 9500 Series



































































Результаты поиска

Содержание MDS 9500 Series

Отзывы:

Похожие инструкции для MDS 9500 Series

Бренды по названию

Популярные бренды

Cisco MDS 9500 Series, Руководство по настройке

Результаты поиска

Содержание MDS 9500 Series

Отзывы:

Похожие инструкции для MDS 9500 Series

Бренды по названию

Популярные бренды