Cisco LightStream 2020 Скачать руководство пользователя страница 26

Страница: 26 / 32

2-26 LightStream 2020 Installation Guide

Basic LS2020 Configuration Tasks

If the network processor is attached to an Ethernet LAN, you will be asked to provide

the IP address and IP subnet mask of the network processor’s on-board Ethernet LAN

interface.

Is the network processor attached to an Ethernet LAN (Y/N)? [N} Y

Configure the IP address for the network processor’s Ethernet LAN interface.

Network Processor Ethernet IP Address [a.b.c.d]: 197.112.23.11

Configure the IP subnet mask for the network processor’s Ethernet LAN interface.

Network Processor Ethernet IP Mask [a.b.c.d]: 255.255.255.0

Is there an IP router on the attached Ethernet LAN (Y/Y)? [N] Y

Configure the Default IP router on the network processor’s Ethernet LAN interface.

Network Processor Ethernet Default IP Router [a.b.c.d]: 197.112.23.1

CHASSIS INFORMATION

Host Name:

LightStream1

Chassis Primary (Active) IP Address:

192.1.1.11

Chassis Secondary IP Address:

<none>

Chassis Subnet Mask:

255.255.255.0

Network Processor Ethernet IP Address:

197.112.23.11

Network Processor Ethernet IP Mask:

255.255.255.0

Network Processor Default IP Router:

197.110.175.2

Chassis configuration contains 1 network processor.

Network processor’s on-board Ethernet LAN interface is attached to an external

Ethernet LAN.

Is the chassis and network processor information correct? (Y/N)? [Y] Y

If you confirm that the configuration data you have entered in this step is correct by
responding

to this query, the script continues with the trunk port configuration query

below.

On the other hand, if you wish to change any configuration data, answer “

” at the chassis

and network processor information query and repeat this step in its entirety. You will be
prompted by the configuration script to re-enter all the applicable network management
information for your LS2020 switch.

Configure trunk port information (Y/N)? [N] N

Creating minimum configuration database...done.

Similarly, if you respond

to the above trunk port configuration query, the system reports

that it is creating a minimum configuration database and that you have completed the basic
configuration procedure.

If you respond “

” to the trunk port configuration query, proceed with Step 6.

Step 5

If your LS2020 switch contains a redundant network processor, continue with the
configuration script, as follows:

Does the chassis contain redundant network processors (Y/N)? [N] Y

Содержание LightStream 2020

































Результаты поиска

Содержание LightStream 2020

Отзывы:

Похожие инструкции для LightStream 2020

Бренды по названию

Популярные бренды

Cisco LightStream 2020, Руководство по установке

Результаты поиска

Содержание LightStream 2020

Отзывы:

Похожие инструкции для LightStream 2020

Бренды по названию

Популярные бренды