background image

C H A P T E R

1

Preface

This preface describes the objectives, audience, organization, and conventions of this guide and describes
related documents that have additional information.

Preface, on page 1

Preface

This preface describes the objectives, audience, organization, and conventions of this guide and describes
related documents that have additional information. It contains the following sections:

Objective

This guide provides an overview and explains how to install, connect, and perform initial configuration for
the device.

Audience

This guide is intended for people who have a high level of technical ability, although they may not have
experience with Cisco software.

Conventions

This section describes the conventions used in this guide.

NOTE

: Means reader take note. Notes contain helpful suggestions or references to additional information

and material.

CAUTION

: This symbol means reader be careful. In this situation, you might do something that could result

in equipment damage or loss of data.

TIP

: Means

the following information will help you solve a problem

. The tip information might not be

troubleshooting or even an action, but could be useful information.

WARNING: IMPORTANT SAFETY INSTRUCTIONSMeans danger. You are in a situation that could
cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical
circuitry and be familiar with standard practices for preventing accidents. Use the statement number

Cisco IC3000 Industrial Compute Gateway Hardware Installation Guide

1

Содержание IC3000





































Отзывы: