Cisco Fourth-Generation Versatile Interface Processor VIP4 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 44

background image

Corporate Headquarters:

Copyright © 2002. Cisco Systems, Inc. All rights reserved.

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Fourth Generation Versatile Interface Processor
(VIP4) Installation and Configuration Guide

Product Numbers: VIP4-50=, VIP4-80=, MEM-VIP4-64M-SD=, MEM-VIP4-128M-SD=, MEM-VIP4-256M-SD=

Introduction

This guide provides instructions for installing, configuring, and maintaining the fourth-generation
Versatile Interface Processor (VIP4). The VIP4 operates with the Cisco 7505, Cisco 7507, Cisco
7507-MX, Cisco 7513, Cisco 7513-MX, and the Cisco 7576 routers with the Route Switch Processor
(RSP1, RSP2, RSP4, RSP4+, or RSP8), and with the Cisco 7000 series routers using the 7000 Series
Route Switch Processor (RSP7000) and 7000 Series Chassis Interface (RSP7000CI). See the

“Software

Requirements” section on page 9

for specific compatibility requirements.

The VIP4 supports online insertion and removal (OIR), which allows you to remove and replace a VIP4
without first shutting down the system. Online insertion and removal maximizes router availability by
letting you add or remove VIP4s during system operation. See the

“Guidelines for VIP4 Removal and

Installation” section on page 15

for more information on removing and installing the VIP4.

The VIP4 supports LAN and WAN port adapters (PAs), including Fast Ethernet, T1/E1, High-Speed
Serial Interface (HSSI), T3/E3, T3/E3 ATM, multichannel T1/E1, multichannel T3/E3, OC-3 ATM,
Packet over SONET (POS), and OC-12 ATM. For a list of supported port adapters, refer to the

“VIP4

and Port Adapter Compatibility” section on page 7

.

The VIP4 port adapters do not support OIR, so when removing or inserting a port adapter, the system
must be shut down first. The VIP42 must be removed from its interface processor slot before removing
or installing a port adapter.

For complete descriptions of interface subcommands and the configuration options available for
VIP4-related interfaces, refer to the configuration note for each of the port adapters installed on your
VIP4 and to the appropriate Cisco IOS software configuration publications. (See the

“Related

Documentation” section on page 2

.)

1
2
3
...
»

Содержание Fourth-Generation Versatile Interface Processor VIP4













































Отзывы:

Нет отзывов

Похожие инструкции для Fourth-Generation Versatile Interface Processor VIP4

Бренд: Danfoss Страницы: 61

Бренд: Yamaha Страницы: 24

Бренд: Yamaha Страницы: 5

Бренд: Zonet Страницы: 8

Бренд: Cypress Semiconductor Страницы: 9

Бренд: BSD Networks Страницы: 7

Бренд: Justec Страницы: 61

Бренд: National Instruments Страницы: 8

Бренд: Selta Страницы: 83

Бренд: Sangoma Страницы: 6

Бренд: PMD Страницы: 74

Бренд: Aewin Technologies Страницы: 86

Бренд: Logicube Страницы: 56

CL-SOM-AM57 Series

Бренд: CompuLab Страницы: 79

Бренд: Renesas Страницы: 40

Бренд: Digital Voice Systems Страницы: 32

IP Board IPT10000C

Бренд: Dialogic Страницы: 2

Бренд: ADS Technologies Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды