Cisco FM1200 Volo Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 175

background image

IMPORTANT

Note that FM Ponte and FM1200 Volo transceivers utilize
different communication protocols, and cannot communicate
with each other.

Unit function and throughput speed

The unit is designed to handle mission-critical video, voice, and data with
extremely high reliability. It can be used to create point-to-point, point-to-
multipoint or mesh network links, with real throughput of up to 150 Mbps
(under optimal wireless link conditions).

Data throttling

The unit's FluidThrottle functionality allows you to specify the maximum
amount of data throughput the unit will be required to handle at any time.
The unit's throughput capacity can be upgraded to different levels using
software plug-ins.

MPLS protocol

Two  different  Multi-Protocol  Label  Switching  (MPLS)-based  protocol
versions can be chosen. If a newer network is being built or upgraded, the
advanced  Prodigy  2.0  protocol  can  be  selected  to  boost  performance.  If
an older network incorporating Cisco components is being upgraded,the
Prodigy  1.0  protocol  with  limited  functionality  can  be  selected  to
guarantee compatibility. Prodigy uses a traffic optimization algorithm that
allows  every  Cisco  radio  to  assign  a  specific  priority  level  to  every
forwarded data packet.

Unit configuration

The  unit  is  compatible  with  Cisco  RACER™.  This  is  a  centralized,
web-based  interface  that  allows  you  to  configure,  monitor,  and
troubleshoot the unit (and in certain cases, the entire wireless network) in
real  time,  without  the  need  for  any  offline  software.  In  cases  where  an
initial  connection  cannot  be  made  to  the  internet,  the  unit  can  be
configured using a built-in offline Configurator interface.

Role adaptability

The  unit  is  equipped  with  FluidMAX.  This  is  a  software  technology  that
allows you to easily change the role of the unit, so that it is able to function
as  part  of  a  Point-to-Point,  Point-to-Multipoint,  or  Mesh  network
architecture without having to replace physical hardware. The unit can use
time-division  multiple  access  (TDMA),  or  carrier  sense  multiple  access
(CSMA) protocols.

Getting Started

© 2021 Cisco and/or its affiliates. All rights reserved.

Page 12 of 175

«
...
10
11
12
13
14
...
»

Содержание FM1200 Volo
















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FM1200 Volo

Beolab transmitter 1

Бренд: Bang & Olufsen Страницы: 30

Бренд: M-system Страницы: 3

Бренд: RadioLink Страницы: 4

Бренд: Radio Industries Страницы: 26

Бренд: S&C Страницы: 62

Skyrider Defiant SX24

Бренд: Hallicrafters Страницы: 9

Бренд: DINUY Страницы: 4

Isotransformer 93-IXFMR3/6-A

Бренд: Charles Страницы: 15

Бренд: Teledyne Страницы: 40

Бренд: Kramer Страницы: 4

Бренд: Daiichi Electronics Страницы: 12

Бренд: Keller-druck Страницы: 2

Бренд: Banner Страницы: 18

Бренд: Grundig Страницы: 6

THERMOPOINT TM/J-500

Бренд: NIVELCO Страницы: 28

Бренд: Denver Страницы: 29

Бренд: MKS Страницы: 42

Бренд: Yaesu Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды