manualshive.com logo in svg

Cisco Firepower 8120, Руководство по началу работы, Страница: 5 / 34

Поделиться
Скачать
Cisco Firepower 8120 Скачать руководство пользователя страница 5

   

      

  Package Contents

Firepower 8000 Series Getting Started Guide

5

Note: 

You cannot connect devices with different configurations; for example, do not connect a Firepower 8250 to 

a Firepower 8350. For more information, see the 

Firepower 8000 Series Hardware Installation Guide

. 

Device Stacks

You can stack devices in the following configurations:

Two Firepower 8140s (not available for Firepower 8120/8130, AMP8050/AMP8150)

Up to four Firepower 8250s, up to four Firepower 8350s, or up to four AMP8350s

A Firepower 8260 (a 10G-capable primary device and a secondary device) 

A Firepower 8360/AMP8360 (a 40G-capable primary device and a secondary device) 

A Firepower 8270 or Firepower 8370/AMP8370 (a 40G-capable primary device and two secondary devices)

A Firepower 8290 or Firepower 8390/AMP8390 (a 40G-capable primary device and three secondary devices)

One device is designated as the primary device and is connected to the network segments. All other devices are 
designated secondary devices, and are used to provide additional resources to the primary device.

Connect the primary device to the network segments you want to analyze in the same way that you would connect 
a single Firepower 8140, Firepower 8250, or Firepower 8350/AMP8350. Connect the secondary devices to the 
primary device as indicated in the stack cabling diagram. If a secondary device contains sensing interfaces, those 
interfaces are not used.

After the devices are physically connected to the network segments and to each other, use a Firepower 
Management Center to establish and manage the stack. See the Firepower 8000 Series Hardware Installation 
Guide for complete information about using devices in stacked configurations. 

Using the 8000 Series Stacking Cable

Install the devices within reach of the three-foot (one-meter) 8000 Series stacking cable to create the physical 
connection between the primary and secondary devices. Stacking two Firepower 8140s requires one cable. 
Stacking the Firepower 8250/8260/8270/8290, Firepower 8350/8360/8370/8390, or 
AMP8350/8360/8370/8390 requires two cables per connection. Devices do not need to be powered down to 
insert or remove the stacking cable.

Stacking Module

Cable: 8000 Series stacking cable

Firepower 8140: one per connection; up to two 
8140 appliances

Firepower 8250/8260/8270/8290: two per 
connection on up to four 8250 appliances

Firepower 8350/8360/8370/8390: two per 
connection on up to four 8350 appliances

AMP8350/8360/8370/8390: two per connection on 
up to four AMP8350 appliances

Содержание Firepower 8120



































Отзывы:

Нет отзывов