background image

 

Connecting Cisco Analog Video Gateway Network Modules to the Network

  Information About the EVM-IPVS-16A Network Module

2

Connecting Cisco Analog Video Gateway Network Modules to the Network

Figure 1

Cisco Analog Video Gateway Network Module (EVM-IPVS-16A) Faceplate

Warning

Equipment connected to outdoor cameras must be permanently grounded in accordance with national 
and local codes. 

Statement 374

Warning

Hazardous voltages may be present in the outdoor camera cables under fault conditions.   Disconnect 
all cables from the outdoor cameras before servicing this equipment. 

Statement 376

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be 
accessed only through the use of a special tool, lock and key, or other means of security. 

Statement 

1017

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. 

Statement 1030

Note

The compact flash module installed in the EVM-IPVS-16A network module is not field-replaceable.

Note

For software-related prerequisites and restrictions, see the 

Cisco Analog Video Gateway 1.0 Installation 

and Upgrade Guide

 at:

http://www.cisco.com/en/US/docs/video/cavg/cavginstall/cavginstall.html

.

Note

For EVM-IPVS-16A network module features and benefits, supported hardware and software, and other 
product information, see the 

Cisco Analog Video Gateway Network Module (EVM-IPVS-16A) Data 

Sheet

Video Ports

16 video ports are provided, video ports 0 and 1 can be configured for input or output. The remaining 14 
video ports can be configured for input only.

1

3210

11

20

EVM

IPVS-16A

170291

Содержание EVM-IPVS-16A















Отзывы: