manualshive.com logo in svg

Cisco CRS Series, Руководство по установке, Страница: 19 / 54

Поделиться
Скачать
Cisco CRS Series Скачать руководство пользователя страница 19

Installing the Chassis Ground Cable

This section describes how to install the chassis ground cable on the Cisco CRS Series Enhanced 16-slot Line
Card Chassis. For complete information on regulatory compliance and safety, see

Regulatory Compliance

and Safety Information for the Cisco CRS Carrier Routing System

.

Prerequisites

Before performing this task, perform the following procedures:

Required Tools and Equipment

You need the following tools and equipment to perform this task:

•

Ground lug

•

Ground cable

•

Crimping tool and lug specific die

•

3/8 in. drive socket wrench

•

10-mm 6 pt. socket

•

Torque wrench with 10-mm 6 pt. socket and rated accuracy at 30 in.-lb (3.39 N-m)

To ensure a satisfactory ground connection, you also need the following parts:

•

One 180-degree angle (straight) grounding lug that has two M6 bolt holes with 0.63 inches (5/8 inch)
(1.60 cm) of spacing center to center between them and a 6 AWG or larger multistrand copper wire.See

Figure 11: 180-Degree (Straight) Chassis Ground Lug, on page 19

.

Figure 11: 180-Degree (Straight) Chassis Ground Lug

•

Two M6 hex head bolts and integrated locking washers are pre-installed on the chassis.

•

Cisco recommend at least 6 AWG multistrand copper ground cable. This cable is not available from
Cisco Systems; it is available from any commercial cable vendor. The cable should be sized according
to local and national installation requirements.

Cisco CRS Routers 16-Slot Line Card Chassis Enhanced Router Installation Guide    

19

Installing Power Components

Installing the Chassis Ground Cable

Содержание CRS Series























































Отзывы:

Нет отзывов