Cisco CPANM-1CE1-B Скачать руководство пользователя страница 1

 1

Doc. No.

Cisco Systems, Inc.
All rights reserved.

170 West Tasman Drive
San Jose, CA 95134-1706
USA

Cisco Systems, Inc.

Corporate Headquarters

Copyright © 1996

1-Port and 2-Port ISDN-PRI Network Module
Configuration Note

Product Numbers:
NM-1CT1, NM-1CT1-CSU, NM-2CT1, NM-2CT1-CSU, NM-1CE1-B, NM-2CE1-B,
NM-1CE1-U, NM-2CE1-U

CPANM-1CT1, CPANM-1CT1-CSU, CPANM-2CT1, CPANM-2CT1-CSU,
CPANM-1CE1-B, CPANM-2CE1-B, CPANM-1CE1-U, CPANM-2CE1-U

This document provides information about the following network modules for the Cisco 3600 series
of modular access routers:

1-port channelized T1/ISDN-PRI network module, Cisco product number NM-1CT1 or
CPANM-1CT1. (See Figure 1.) This module will also be referred to as the 1-port CT1/PRI
network module.

2-port channelized T1/ISDN-PRI network module, Cisco product number NM-2CT1 or
CPANM-2CT1. (See Figure 2.) This module will also be referred to as the 2-port CT1/PRI
network module.

1-port channelized T1/ISDN-PRI with CSU network module, Cisco product number
NM-1CT1-CSU or CPANM-1CT1-CSU. (See Figure 3.) This module will also be referred to as
the 1-port CT1/PRI-CSU network module.

2-port channelized T1/ISDN-PRI with CSU network module, Cisco product number
NM-2CT1-CSU or CPANM-2CT1-CSU. (See Figure 4.) This module will also be referred to as
the 2-port CT1/PRI-CSU network module.

1-port channelized E1/ISDN-PRI balanced (120-ohm) network module, Cisco product number
NM-1CE1B or CPANM-1CE1B. (See Figure 5.) This module will also be referred to as the 1-port
CE1/PRI-B network module.

78-3052-01

Содержание CPANM-1CE1-B

























Отзывы: