manualshive.com logo in svg

Cisco Catalyst 3130, Руководство по настройке программного обеспечения

Cisco Catalyst 3130 - сетевой коммутатор с широкими возможностями управления и конфигурации. Пользователи могут загрузить бесплатное руководство по настройке программного обеспечения с официального сайта. Настройте свою сеть с легкостью, следуя инструкциям в Software Configuration Manual для Catalyst 3130. Более подробную информацию можно найти на manualshive.com.

Поделиться
Скачать
background image

 

14-2

Cisco Catalyst Blade Switch 3130 and 3032 for Dell Software Configuration Guide

OL-12247-04

Chapter 14      Configuring VTP

Understanding VTP

The switch supports 1005 VLANs, but the number of routed ports, SVIs, and other configured features 
affects the usage of the switch hardware. If the switch is notified by VTP of a new VLAN and the switch 
is already using the maximum available hardware resources, it sends a message that there are not enough 
hardware resources available and shuts down the VLAN. The output of the 

show vlan

 user EXEC 

command shows the VLAN in a suspended state.

VTP version 1 and version 2 support only normal-range VLANs (VLAN IDs 1 to 1005). Cisco IOS 
Release 12.2(52)SE and later support VTP version 3. VTP version 3 supports the entire VLAN range 
(VLANs 1 to 4094). Extended range VLANs (VLANs 1006 to 4094) are supported only in VTP 
version 3. You cannot convert from VTP version 3 to VTP version 2 if extended VLANs are configured 
in the domain. 

These sections contain this conceptual information:

•

The VTP Domain, page 14-2

•

VTP Modes, page 14-3

•

VTP Advertisements, page 14-4

•

VTP Version 2, page 14-4

•

VTP Version 3, page 14-5

•

VTP Pruning, page 14-6

•

VTP and Switch Stacks, page 14-8

The VTP Domain 

A VTP domain (also called a VLAN management domain) consists of one switch or several 
interconnected switches or switch stacks under the same administrative responsibility sharing the same 
VTP domain name. A switch can be in only one VTP domain. You make global VLAN configuration 
changes for the domain.

By default, the switch is in the VTP no-management-domain state until it receives an advertisement for 
a domain over a trunk link (a link that carries the traffic of multiple VLANs) or until you configure a 
domain name. Until the management domain name is specified or learned, you cannot create or modify 
VLANs on a VTP server, and VLAN information is not propagated over the network.

If the switch receives a VTP advertisement over a trunk link, it inherits the management domain name 
and the VTP configuration revision number. The switch then ignores advertisements with a different 
domain name or an earlier configuration revision number.

Caution

Before adding a VTP client switch to a VTP domain, always verify that its VTP configuration revision 
number is 

lower

 than the configuration revision number of the other switches in the VTP domain. 

Switches in a VTP domain always use the VLAN configuration of the switch with the highest VTP 
configuration revision number. If you add a switch that has a revision number higher than the revision 
number in the VTP domain, it can erase all VLAN information from the VTP server and VTP domain. 
See the 

“Adding a VTP Client Switch to a VTP Domain” section on page 14-17

 for the procedure for 

verifying and resetting the VTP configuration revision number.

When you make a change to the VLAN configuration on a VTP server, the change is propagated to all 
switches in the VTP domain. VTP advertisements are sent over all IEEE trunk connections, including 
Inter-Switch Link (ISL) and IEEE 802.1Q. VTP dynamically maps VLANs with unique names and 
internal index associates across multiple LAN types. Mapping eliminates excessive device 
administration required from network administrators.

Содержание Catalyst 3130











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3130

Fujitsu MB91401 Datasheet preview
MB91401
Бренд: Fujitsu Страницы: 72
D-Link DIR-330 - Wireless G VPN Router Brochure & Specs preview
DIR-330 - Wireless G VPN Router
Бренд: D-Link Страницы: 3
BluePoint Security AdTrap AT1000 User Manual preview
AdTrap AT1000
Бренд: BluePoint Security Страницы: 18
ADTRAN 1202361L2 Hardware Installation Manual preview
1202361L2
Бренд: ADTRAN Страницы: 38
Atlante Informatica Nano Cluster APU2 First Configuration preview
Nano Cluster APU2
Бренд: Atlante Informatica Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды