Cisco CableCARD Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 184

background image

Determine Available Bandwidth for Multiple Bootloaders

734375 Rev H

139

7

Is there enough bandwidth to add the new bootloader carousels? (Bootloader
carousels require data rates between 1.00 and 3.00 Mbps.)



If

yes

, go to

Verify a VCI for Inband BFS Sources on BFS BIG Systems

(on



If

no

, refer to

Recommendations for Data Carousel Rate Management Technical

Bulletin

(part number 716377) for details on how to increase the bandwidth of

your system.

Verify a VCI for Inband BFS Sources on BFS BIG Systems

This section describes how to check the number of BFS sessions on your system to
determine whether any unused VCIs are present for the inband BFS carousel.

Notes:



Your network was initially installed and reserved with 20 Virtual Channel
Indicator (VCI) connections (values 256-275) on the ATM switch. The VCIs carry
inband BFS information from the DNCS to the BIG. Because you will create a
new inband source, you must make sure that one VCI is available for each
additional bootloader carousel that you add to the DNCS.



If you need detailed instructions for this procedure, refer to the manual that
came with your ATM switch.

Complete the following steps to determine whether there are enough unused VCIs
available for the additional inband BFS carousels.

1

Using the manual that came with your ATM switch, check the ATM switch to
determine the number of unused VCIs.

2

Are there enough VCIs for the new bootloader carousels?



If

yes

, go to

Adding a Bootloader Source to the DNCS

(on page 142).



If

no

, add more VCIs to the switch. Then, go to

Adding a Bootloader Source

to the DNCS

(on page 142).

Note:

Having unused VCIs does not present any issues to your system;

therefore, we recommend that you create 5 to 10 extra VCIs.

«
...
147
148
149
150
151
...
»

Содержание CableCARD

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CableCARD

SignalPilot 51840

Бренд: Esu Страницы: 32

Бренд: Lika Страницы: 2

Бренд: de Gier Страницы: 26

Бренд: Transition Networks Страницы: 7

Бренд: Xantrex Страницы: 36

Бренд: OLYS Страницы: 3

Бренд: Danfoss Страницы: 148

Бренд: iBasso Audio Страницы: 64

Бренд: PTN Страницы: 12

Бренд: Fischer Panda Страницы: 218

Бренд: R&S Страницы: 24

Бренд: Channel Vision Страницы: 2

Бренд: Tektronix Страницы: 12

Бренд: TRENDnet Страницы: 1

Бренд: Denon Страницы: 9

Бренд: B&B Страницы: 36

Бренд: EasyDrive Electric Страницы: 106

Бренд: i3 International Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды