Cisco C9124AXD Скачать руководство пользователя страница 38

Страница: 38 / 118

• (Optional) Mounting brackets only if you opted for these when ordering the AP.

If any item is missing or damaged, contact your Cisco representative or reseller for instructions.

Optional Tools and Hardware from Cisco

Depending on what you ordered, the following optional equipment may be part of your shipment:

•

Cisco Orderable Accessories, on page 30

• AP paintable cover C9124-CVR1= Spare only

• Spare part kit containing extra cable glands, power connector, ground lug, and so on. (AIR-ACC-KIT1=)

Additional Tools and Hardware Required for Installation

You must independently procure the following tools and materials, which might be required during various
stages of installing the AP:

• Ground lug crimping tool (Panduit CT-720 with CD-720-1 die)

• #2 Phillips Screwdriver

• 5–mm Hex driver or Allen wrench

• Adjustable wrench or 28–mm box wrench

• 6-AWG copper ground wire

• 10–mm open-end or box wrench

• 13–mm box-end wrench or socket set

• 16–mm box-end wrench or socket set

• Large flat or Phillips screwdriver (for SFP port plug)

• 2.54–mm (0.10 inch) hex crimp tool for DC power connector

• Shielded outdoor-rated Ethernet (CAT5e or better) cable of 0.20 to 0.35 inch (5 to 9 mm) diameter.

• Ethernet RJ-45 connector and installation tool

• Shielded outdoor-rated DC power cable with 18–AWG 2 conductor, 0.21 to 0.35 inch (5.5 to 9.0mm)

outer diameter

• Ground rod, as required by local regulations

Cisco Orderable Accessories

Order the following accessories separately from Cisco:

Cisco Catalyst 9124AX Series Outdoor Access Point Hardware Installation Guide

Unpacking Your Access Point

Optional Tools and Hardware from Cisco

Содержание C9124AXD























































































































Результаты поиска

Содержание C9124AXD

Отзывы:

Похожие инструкции для C9124AXD

Бренды по названию

Популярные бренды

Cisco C9124AXD, Руководство по установке оборудования

Результаты поиска

Содержание C9124AXD

Отзывы:

Похожие инструкции для C9124AXD

Бренды по названию

Популярные бренды