Cisco BTS 10200 Скачать руководство пользователя страница 13

Страница: 13 / 62

1-7

Cisco BTS 10200 Softswitch ISDN Provisioning and Troubleshooting

OL-12436-02

Chapter 1 ISDN Provisioning

Cisco BTS 10200 Provisioning

Figure 1-5

Sample Configuration for Backhaul Session Connections Between a CA and a
Gateway

Step 3

Configure PRI FAS.

Figure 1-6

shows a sample configuration for Facility Associated Signaling (FAS).

Note

To configure PRI NFAS, go to

Step 4

Figure 1-6

Sample Configuration for FAS

Add an ISDN D-channel profile with the nfas-supp token set to N.

add isdn-dchan-profile id=NI2; description=dallas isdn dchan profile no.1;

type=swv-us-ni2-pri; interface-type=network; isdn-restart-pri-supp=y;

isdn-restart-interface-supp=y;isdn-service-supp=n; isdn-restart-chan-supp=y;

isdn-farend-init=n;isdn-query-supp=n;nfas-supp=n; bchan-neg-supp=y; t-301=300;

t-302=10; t-303=4; t-305=30;t-308=4; t-309=90;t-310=10; t-316=30; t-321=20;t-322=4;

t-323=30;

Note

See the

“ISDN Profiles” section on page 1-16

for more information.

Add the ISDN interfaces.

add isdn-intf isdn-dchan-id=100; intf=0;

Add the ISDN D channels using the backhaul session set ID added in Step 2c and ISDN interfaces
added in Step 3b (where dchan-port refers to the DS1 span number used).

add isdn-dchan id=100; backhaul-type=RUDP;SET-ID=backset1; dchan-slot=0;

dchan-port=1; dchan-type=primary; dchan-intf=0;isdn-dchan-profile-id=NI2;

Primary Call Agent

Gateway

Set 1

Group 1

Session 1

Session 2

Session 3

Session 4

Group 2

Ethernet Port 1

(10.89.225.223)

UDP port 9000

Ethernet Port 2

(10.89.226.224)

UDP port 9001

Ethernet Port 1

(10.89.225.224)

UDP port 9000

Ethernet Port 2

(10.89.226.223)

UDP port 9001

Ethernet Port 1

(10.89.227.200)

UDP port 9001

Secondary Call Agent

69960

Ethernet Port 1

(10.89.227.200)

UDP port 9000

D Channel

Trunk group (100)

CIC start - 1

CIC end - 23

Interface - 0

69722

23 24

Содержание BTS 10200































































Результаты поиска

Содержание BTS 10200

Отзывы:

Похожие инструкции для BTS 10200

Бренды по названию

Популярные бренды

Cisco BTS 10200, Руководство по устранению неисправностей

Результаты поиска

Содержание BTS 10200

Отзывы:

Похожие инструкции для BTS 10200

Бренды по названию

Популярные бренды