Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 714

Страница: 714 / 874

15-88

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15 Diagnostic Tests

Enhanced Traffic Measurement

Call Processing Counters

Table 15-10

identifies the Call Processing counters and their meanings.

Table 15-10

Call Processing Counters

Counter Label

Counter Context

CALLP_ORIG_ATTMP

The number of originating call attempts of all types on the reporting call
agent.

CALLP_TERM_ATTMP

The number of terminating call attempts of all types on the reporting call
agent.

CALLP_ORIG_FAIL

The number of originating call attempts of all types that failed on the
reporting call agent.

CALLP_TERM_FAIL

The number of terminating call attempts of all types that failed on the
reporting call agent.

CALLP_CALL_SUCC

The number of successful originating and terminating call attempts of all
types on the reporting call agent.

CALLP_CALL_ABAND

The number of originating call attempts of all types that were abandoned
on the reporting call agent.

CALLP_ISDN_ORIG_ATTMP

The number of originating ISDN call attempts on the reporting call agent.

CALLP_ISDN_TERM_ATTMP

The number of ISDN terminating call attempts on the reporting call agent.

CALLP_ISDN_ORIG_FAIL

The number of ISDN originating call attempts that failed on the reporting
call agent.

CALLP_ISDN_TERM_FAIL

The number of ISDN terminating call attempts that failed on the reporting
call agent.

CALLP_ISDN_CALL_SUCC

The number of successful ISDN originating and terminating call attempts
on the reporting call agent.

CALLP_ISDN_CALL_ABAND

The number of ISDN originating call attempts that were abandoned on the
reporting call agent.

CALLP_SS7_ORIG_ATTMP

The number of originating SS7 call attempts on the reporting call agent.

CALLP_SS7_TERM_ATTMP

The number of SS7 terminating call attempts on the reporting call agent.

CALLP_SS7_ORIG_FAIL

The number of SS7 originating call attempts that failed on the reporting
call agent.

CALLP_SS7_TERM_FAIL

The number of SS7 terminating call attempts that failed on the reporting
call agent.

CALLP_SS7_CALL_SUCC

The number of successful SS7 originating and terminating call attempts
on the reporting call agent.

CALLP_SS7_CALL_ABAND

The number of SS7 originating call attempts that were abandoned on the
reporting call agent.

CALLP_SIP_ORIG_ATTMP

The number of originating SIP call attempts on the reporting call agent.

CALLP_SIP_TERM_ATTMP

The number of SIP terminating call attempts on the reporting call agent.

CALLP_SIP_ORIG_FAIL

The number of SIP originating call attempts that failed on the reporting
call agent.

CALLP_SIP_TERM_FAIL

The number of SIP terminating call attempts that failed on the reporting
call agent.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание BTS 10200 Softswitch

Отзывы:

Бренды по названию

Популярные бренды

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Результаты поиска

Содержание BTS 10200 Softswitch

Отзывы:

Бренды по названию

Популярные бренды