manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 589

 

14-15

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 14      General Troubleshooting

Protocol Troubleshooting

  •

Endpoint malfunctioning.

  •

Loss of lower connectivity.

  •

Endpoint taken out of service.

  •

No fault reason available.

Protocol Troubleshooting

This section provides the troubleshooting information for resolving BTS 10200 protocol problems.

Troubleshooting Signaling System 7 SIGTRAN Problems

This section describes tools and procedures for troubleshooting SIGTRAN problems on the BTS 10200 
and Cisco ITP. It also describes how to clear SIGTRAN related BTS 10200 alarms. In the descriptions 
within, a series of steps may be required to determine the source of the problem and may include viewing 
other alarms, invoking command-line interface (CLI) status and control commands, viewing the BTS 
10200 logs, and invoking ITP control and status requests.

For details on Cisco ITP operations, refer to the 

Cisco IP Transfer Point Manual

 at the following url:

http://www.cisco.com/univercd/cc/td/doc/product/wireless/moblwrls/itp/

This section contains the following sections:

  •

Cisco Internet Protocol Transfer Point Troubleshooting Procedures

  •

Viewing BTS 10200 Logs

  •

'Troubleshooting Transaction Capabilities Application Part with the Query Verification Tool

Cisco Internet Protocol Transfer Point Troubleshooting Procedures

The following procedures are useful for troubleshooting problems on the Cisco ITP. This section 
contains the following procedures:

  •

Internet Protocol Transfer Point System Messages

  •

Logging On to the Internet Protocol Transfer Point

  •

Viewing the Internet Protocol Transfer Point Configuration

  •

Internet Protocol Transfer Point Status Commands

  •

Controlling Internet Protocol Transfer Point Resources

Internet Protocol Transfer Point System Messages

The Cisco ITP displays system messages when you are logged in to the console port. Some of these 
messages are similar to alarms. Analyzing ITP system messages is outside the scope of this document. 
For details concerning ITP system messages, please see the ITP Operations Manual at:

http://www.cisco.com/univercd/cc/td/doc/product/wireless/moblwrls/itp/23sw/index.htm

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды