manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 353

 

8-9

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 8      Operations Support System Troubleshooting

Monitoring Operations Support System Events

Monitoring Operations Support System Events

This section provides the information needed to monitor and correct OSS events. 

Table 8-2

 lists all of 

the OSS events in numerical order and provides cross reference to each subsection in this section.

Test Report—Operations Support System (1)

The Test Report event is for testing the operations support system event category. The event is 
informational and no further action is required.

Undefined Variable in Known Set—Operations Support System (2)

The Undefined Variable in Known Set alarm (major) indicates that there was not a definition for a data 
column that could be found in the database. To troubleshoot and correct the cause of the Undefined 
Variable in Known Set alarm, refer to the 

“Undefined Variable in Known Set—Operations Support 

System (2)” section on page 8-13

.

Table 8-2

BTS 10200 OSS Events 

Event Type

Event Name

Event Severity

OSS(1)

Test Report—Operations Support System (1)

INFO

OSS(2)

Undefined Variable in Known Set—Operations Support System (2)

MAJOR

OSS(3)

Undefined Data Column Identification—Operations Support System (3)

MAJOR

OSS(4)

Request Handler Instantiation Error—Operations Support System (4)

MAJOR

OSS(5)

Structured Query Language Error While Getting Statistics—Operations Support 
System (5)

MINOR

OSS(6)

Structured Query Language Connection Error—Operations Support System (6)

MAJOR

OSS(7)

Simple Network Management Protocol File Read Error—Operations Support System 
(7)

WARNING

OSS(8)

No Reply Received from Destination—Operations Support System (8)

MINOR

OSS(9)

Simple Network Management Protocol Authentication Error—Operations Support 
System (9)

MINOR

OSS(10)

Queue Processing Module Database Management Index Failed with 
Error—Operations Support System (10)

MAJOR

OSS(11)

Queue Processing Module Database Management Index Mismatch During Add or 
Delete—Operations Support System (11)

WARNING

OSS(12)

User Session Count is Approaching Threshold Limit—Operation Support System 
(12)

WARNING

OSS(14)

User Session Count Exceeds Major Threshold Limit—Operation Support System 
(14)

MAJOR

OSS(16)

Session Has Been Removed by Session Control Policy —Operation Support System 
(16)

INFO

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды