Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 132

Страница: 132 / 874

3-26

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 3 Billing Troubleshooting

Monitoring Billing Events

This section provides the information needed to monitor and correct billing events.

Table 3-2

lists all of

the billing events in numerical order and provides cross reference to each subsection in this section.

Table 3-2

BTS 10200 Billing Events

Event Type

Event Name

Event Severity

BILLING(1)

Test Report—Billing (1)

INFO

BILLING(2)

Billing Partition Disk Usage Minor Threshold Exceeded—Billing (2)

MINOR

BILLING(3)

Billing Partition Disk Usage Major Threshold Exceeded—Billing (3)

MAJOR

BILLING(4)

Billing Partition Disk Usage Critical Threshold Exceeded—Billing (4)

CRITICAL

BILLING(5)

Billing Partition Disk Usage Within Normal Range—Billing (5)

INFO

BILLING(6)

File Transfer Protocol/Secure File Transfer Protocol Transfer Failed—Billing (6)

MAJOR

BILLING(7)

Transmission Control Protocol Connection Error—Billing (7)

CRITICAL

BILLING(8)

Transmission Control Protocol Packet Receive Failure—Billing (8)

MAJOR

BILLING(13)

Database Connection Error—Billing (13)

CRITICAL

BILLING(14)

File Open Error—Billing (14)

WARNING

BILLING(15)

File Write Error—Billing (15)

MAJOR

BILLING(29)

Call Data Block Send Failed—Billing (29)

MAJOR

BILLING(30)

Domain Name Mapping Failed—Billing (30)

MAJOR

BILLING(31)

Port not Specified—Billing (31)

MAJOR

BILLING(32)

Element Management System Address not Specified—Billing (32)

MAJOR

BILLING(33)

File Transfer Protocol/Secure File Transfer Protocol Parameters Invalid—Billing
(33)

MAJOR

BILLING(35)

All Billing Links at Billing Server Down—Billing (35)

CRITICAL

BILLING(36)

Billing Link Restored—Billing (36)

INFO

BILLING(37)

Billing Link Failure—Billing (37)

MAJOR

BILLING(38)

Event Message Log File Access Error—Billing (38)

MAJOR

BILLING(40)

Event Message Encode Failure—Billing (40)

MINOR

BILLING(41)

Message Content Error—Billing (41)

MINOR

BILLING(42)

Error Reading Provisioned Data–Using Default—Billing (42)

WARNING

BILLING(44)

Record Keeping System Switch Occurred—Billing (44)

MAJOR

BILLING(45)

Event Message Log File Opened—Billing (45)

MINOR

BILLING(46)

Event Message Log File Closed—Billing (46)

MINOR

BILLING(47)

Record Keeping System Unreachable for One Hour—Billing (47)

MINOR

BILLING(48)

Record Keeping System Unreachable for Three Hours—Billing (48)

MAJOR

BILLING(49)

Record Keeping System Unreachable for Five Hours—Billing (49)

CRITICAL

BILLING(52)

Bulk Data Management System Stopped Generating New Billing File—Billing (52)

CRITICAL

BILLING(53)

Event Message Disk Space 50 Percent Full—Billing (53)

MINOR

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание BTS 10200 Softswitch

Отзывы:

Бренды по названию

Популярные бренды

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Результаты поиска

Содержание BTS 10200 Softswitch

Отзывы:

Бренды по названию

Популярные бренды