Cisco ASR 920 series Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 438

background image

Layer 2 Protocol Peering

For Layer 2 protocols (CDP, UDLD, LLDP, MSTP, LACP,PTP peer delay, ELMI, LOAM ) to peer with a
neighbor on a port that has an EFP service instance configured, you need to enter the

l2 protocol peer protocol

service-instance configuration command on the service instance.

This example shows how to configure CDP to peer with a neighbor on a service instance:

Router (config)# interface gigabitethernet0/1
Router (config-if)# service instance 1 Ethernet
Router (config-if-srv)# encapsulation untagged
Router (config-if-srv)# l2protocol peer cdp
Router (config-if-srv)# bridge-domain 10
Router (config-if-srv)# end

Layer 2 Protocol Forwarding

Layer 2 protocol forwarding is based on the bridge domain ID and the destination MAC address.

Selecting the l2protocol forward option causes the router to flood interfaces in the same VLAN or bridge-domain
with untagged or tagged BPDU packets. You can apply the l2protocol forward command to CDP, LACP,
LLDP, PAGP, STP, UDLD, and VTP traffic. This is an example how to configure the l2protocol forward
option:

interface GigabitEthernet0/9
ethernet uni id PRAV-PE2
service instance 1 ethernet
encapsulation untagged
l2protocol forward cdp
bridge-domain 500
!
service instance 10 ethernet xcon

encapsulation dot1q 100
l2protocol forward cdp
xconnect 4.3.2.1 12 encapsulation mpls

!

Configuring IEEE 802.1Q Tunneling and Layer 2 Protocol Tunneling Using EFPs

Tunneling is a feature used by service providers whose networks carry traffic of multiple customers and who
are required to maintain the VLAN and Layer 2 protocol configurations of each customer without impacting
the traffic of other customers. The router uses EFPs to support QinQ and Layer 2 protocol tunneling.

802.1Q Tunneling (QinQ)

Service provider customers often have specific requirements for VLAN IDs and the number of VLANs to be
supported. The VLAN ranges required by different customers in the same service-provider network might
overlap, and traffic of customers through the infrastructure might be mixed. Assigning a unique range of
VLAN IDs to each customer would restrict customer configurations and could easily exceed the VLAN limit
(4096) of the 802.1Q specification.

Using the EVCs, service providers can encapsulate packets that enter the service-provider network with
multiple customer VLAN IDs (C-VLANs) and a single 0x8100 Ethertype VLAN tag with a service provider
VLAN (S-VLAN). Within the service provider network, packets are switched based on the S-VLAN. When

Carrier Ethernet Configuration Guide (Cisco ASR 920 Series)

30

Ethernet Virtual Connections Configuration

Layer 2 Protocol Peering

«
...
46
47
48
49
50
...
»

Содержание ASR 920 series























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 920 series

Бренд: D-Link Страницы: 2

Verizon DSL-2750B

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 38

Бренд: D-Link Страницы: 29

DGS-3700 Series

Бренд: D-Link Страницы: 292

Бренд: D-Link Страницы: 140

DGS-1224T - Web Smart Switch

Бренд: D-Link Страницы: 61

DI-LB604 - Load Balancing Router

Бренд: D-Link Страницы: 14

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 45

Бренд: D-Link Страницы: 218

DES-3528 - xStack Switch - Stackable

Бренд: D-Link Страницы: 322

DIR-130 - Broadband VPN Router

Бренд: D-Link Страницы: 10

DIR-130 - Broadband VPN Router

Бренд: D-Link Страницы: 4

DIR-130 - Broadband VPN Router

Бренд: D-Link Страницы: 13

Бренд: D-Link Страницы: 13

DI-804HV - Express ENwork Router

Бренд: D-Link Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды