manualshive.com logo in svg

Cisco ASR 920 series, Руководство по установке оборудования

Поделиться
Скачать
Cisco ASR 920 series Скачать руководство пользователя страница 28

   

2-6

Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide

OL-32751-01

Chapter 2      Preparing for Installation

Safety Guidelines

Warning

Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry 
tub, in a wet basement, or near a swimming pool. 

Statement 1035

Warning

Before opening the unit, disconnect the telephone-network cables to avoid contact with 
telephone-network voltages. 

Statement 1041

Warning

This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. 
Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The 
telecommunications lines must be disconnected 1) before unplugging the main power connector or 2) 
while the housing is open, or both. 

Statement 1043

Warning

This product requires short-circuit (overturned) protection, to be provided as part of the building 
installation. Install only in accordance with national and local wiring regulations. 

Statement 1045

Warning

When installing or replacing the unit, the ground connection must always be made first and 
disconnected last. 

Statement 1046

Warning

Failure to securely tighten the power and relay connector captive screws can result in an electrical 
arc if the connector is accidentally removed. 

Statement 1058

Warning

This equipment is intended to be grounded. Ensure that the host is connected to earth ground during 
normal use. 

Statement 39

Warning

If you connect or disconnect the console cable with power applied to the switch or any device on the 
network, an electrical arc can occur. This could cause an explosion in hazardous location 
installations. Be sure that power is removed or the area is nonhazardous before proceeding. To verify 
switch operation, perform POST on the switch in a nonhazardous location before installation. 

Statement 1065

Warning

Installation of the equipment must comply with local and national electrical codes. 

Statement 1074

Warning

Hazardous voltage or energy may be present on DC power terminals. Always replace cover when 
terminals are not in service. Be sure uninsulated conductors are not accessible when cover is in 
place. 

Statement 1075

When working on equipment powered by electricity, follow these guidelines: 

•

Locate the room’s emergency power-off switch. If an electrical accident occurs, you will be able to 
quickly turn off the power.

Содержание ASR 920 series















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды