Cisco ASR-920-12SZ-IM Скачать руководство пользователя страница 23

Страница: 23 / 25

Last reset cause: RSP-Board
UEA platform with 2097152 Kbytes of main memory

Step 5

Remove power cables, if any, from the Cisco ASR 920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Router:

• For power supplies with a circuit breaker switch, position the switch to the Off (O) position.
• For power supplies with a standby switch, place the standby switch in the Standby position.

After powering off the router, wait for a minimum of 30 seconds before powering it on again.

Note

Related Documents

• Cisco ASR 920 and ASR 920U Aggregation Services Router Hardware Installation Guide can be viewed at:

https://www.cisco.com/

c/en/us/td/docs/routers/asr920/hardware/installation/guide-12sz-im/b-asr-920-12-SZ-IM.html

• The documentation for the supported software features can be viewed at

https://www.cisco.com/c/en/us/support/routers/

asr-920-series-aggregation-services-router/products-installation-and-configuration-guides-list.html

Содержание ASR-920-12SZ-IM


























Результаты поиска

Содержание ASR-920-12SZ-IM

Отзывы:

Похожие инструкции для ASR-920-12SZ-IM

Бренды по названию

Популярные бренды

Cisco ASR-920-12SZ-IM, Быстрый старт

Результаты поиска

Содержание ASR-920-12SZ-IM

Отзывы:

Похожие инструкции для ASR-920-12SZ-IM

Бренды по названию

Популярные бренды