Cisco ASR 907 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 204

background image

Temperature Sensor

The Cisco ASR 907 Router has a temperature sensor to detect ambient overtemperature conditions inside the
chassis. The operating temperature range is between –40 C to +65 C. Temperatures outside this range are
reported to the processor as an interrupt, and the software takes action to generate the appropriate alarms.

Interface Numbering

Following is an explanation of the slot or port numbering:

• The numbering format is

Interface type slot or interface number

. Interface (port) numbers begin at

logical 0 for each interface type.

• Interface module slots are numbered from bottom to top, with logical interfaces on each module numbered

from left to right. Interfaces are hard-wired. Therefore, port 0 is always logical interface 0/0, port 1 is
always logical interface 0/1, and so on.

Following is the A900-RSP4 port numbering:

• For IM N560-IMA2C the port numbering is

HundredGigE

— 0/0/0/0 - 0/0/0/1

• For IM A900-IMA8Z the port numbering is

TenGigE

— 0/0/0/1 - 0/0/0/7

• For IM A900-IMA8CS1Z-M the port numbering is:

•

GigE

— 0/0/0/0 - 0/0/0/15

•

TenGigE

— 0/0/0

/16

The following commands display the active RP slot number. The interface module is referenced as 1/x instead
of 0/x:

•

show diag all eeprom detail

•

show platform software trace message iomd

•

show platform software agent iomd

•

show platform software peer shell-manager brief

•

show platform software peer chassis-manager

•

show platform software memory iomd

•

set platform software trace iomd

Regulatory Compliance

For regulatory compliance and safety information, see the Regulatory Compliance and Safety Information
for the Cisco ASR_900 Series Aggregation Routers document.

6

Slot 0 is not supported in A900-IMA8CS1Z-M

Cisco ASR 907 Router Hardware Installation Guide

29

Cisco ASR 907 Router Overview

Temperature Sensor

«
...
37
38
39
40
41
...
»

Содержание ASR 907













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 907

Бренд: PaloAlto Networks Страницы: 3

Бренд: FOR-A Страницы: 72

3C410012A - OfficeConnect Remote 531 Access...

Бренд: 3Com Страницы: 72

Бренд: Stephen Страницы: 102

ConnectX-3 Pro MCX349A-XCCN

Бренд: Mellanox Technologies Страницы: 35

SteelCentral AppResponse 2180

Бренд: Riverbed Страницы: 82

Бренд: AMX Страницы: 1

Бренд: Patton electronics Страницы: 2

Бренд: ZyXEL Communications Страницы: 3

Бренд: Stephen Страницы: 8

GigaSpire BLAST u6

Бренд: Calix Страницы: 9

Cradlepoint AER1600

Бренд: Choose 2 rent Страницы: 5

Бренд: C&H Technologies Страницы: 1

Бренд: D-Link Страницы: 191

Бренд: Cisco Страницы: 14

RouterBOARD 711-5HnD

Бренд: MikroTik Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды