Cisco ASR 901S Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 106

background image

C H A P T E R

3

Installing the Router

This chapter describes the safety information, equipment, and procedures required to mount the Cisco ASR
901S Series Aggregation Services Router onto a vertical pole or wall. This chapter contains these sections:

•

Mounting Kits Overview, page 23

•

General Safety Information for Mounting, page 24

•

Contents of the Mounting Kits, page 25

•

Customer-Supplied Materials and Tools, page 30

•

Router-Mounting Instructions, page 31

•

Connecting the Chassis Ground and Power, page 45

•

Opening the Router Chassis, page 48

•

Power Connection Compliance, page 52

•

Assembling and Connecting the DC Power Cable to the Router, page 52

•

AC Power Cable, page 55

•

Connecting the AC Power Cable to the Router, page 56

•

Connecting Cables, page 57

•

Enabling Zero Touch Provisioning on the Router, page 67

•

Accessing the Router in Freezing Temperature, page 69

•

Powering on the Router, page 69

•

Using CLIs for Flash Memory and Directory Procedures, page 70

•

What to do After Installing the Hardware, page 74

Mounting Kits Overview

You will need some or all of the kits described in this section to install the router in the outside plant (OSP).
Your installation environment and requirements determine the kits you need.

The includes a detailed description of each kit.

Cisco ASR 901S Series Aggregation Services Router Hardware Installation Guide

OL-29732-01

23

«
...
31
32
33
34
35
...
»

Содержание ASR 901S Series











































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 901S Series

Бренд: Opvimus Страницы: 12

Бренд: QNO Страницы: 106

Бренд: Face Страницы: 8

Бренд: Garland Страницы: 43

Бренд: Ravpower Страницы: 27

Extreme Gaming VGA Cooler GV1000

Бренд: ZALMAN Страницы: 7

Бренд: Abit Страницы: 22

Suzie-Q 541.35.520

Бренд: Hafele Страницы: 12

Бренд: ADTRAN Страницы: 20

Бренд: M-system Страницы: 4

Бренд: Kramer Страницы: 56

Бренд: Kasda Страницы: 39

8-Port 10/100Mbps Fast Ethernet Switch

Бренд: Amer.com Страницы: 14

Бренд: Matrix Switch Corporation Страницы: 54

Бренд: TRENDnet Страницы: 7

Бренд: MESA Electronic Страницы: 27

Бренд: Airlinkplus Страницы: 24

Бренд: Radio Shack Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды