Cisco ASR 901S Series Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 106

background image

Alarm Port Pinouts

The following table lists the pinouts for the alarm port (RJ45) on the Cisco ASR 901S Series Aggregation
Series Router.
The router supports four alarm inputs. The alarm input is a dry contact alarm port. Use the alarm CLI to define
each alarm input to respond to a normally open or closed dry-contact closure and to define the alarm severity
as minor, major, or critical.

Description

Signal Name

Pin

—

Alarm input 1

1

—

Alarm input 2

2

Not connected

—

3

—

Alarm input 3

4

—

Alarm input 4

5

Not connected

—

6

Not connected

—

7

—

Alarm common

8

Management Ethernet Port Pinouts

The following table lists the pinouts for the management Ethernet port (RJ-45) on the Cisco ASR 901S Series
Aggregation Services Router.

Cisco ASR 901S Series Aggregation Services Router Hardware Installation Guide

94

OL-29732-01

Cable Specifications

Alarm Port Pinouts

«
...
102
103
104
105
106
»

Содержание ASR 901S Series











































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 901S Series

Бренд: Farallon Страницы: 26

Бренд: Observint Страницы: 11

QSR-3920 Series

Бренд: QTech Страницы: 120

Бренд: QSC Страницы: 28

Бренд: Zenith Data Systems Страницы: 64

Бренд: Blackrock Microsystems Страницы: 27

DM/IP601-CPCI-100BT

Бренд: Dialogic Страницы: 2

Бренд: Zonet Страницы: 53

Бренд: Magnadyne Страницы: 8

IMACS Network Device

Бренд: Zhone Страницы: 114

Бренд: Z Microsystems Страницы: 51

Бренд: AXAGO Страницы: 2

Бренд: Promise Technology Страницы: 26

Бренд: Solwise Страницы: 231

BiPAC 5200S RC Series

Бренд: Billion Страницы: 79

Бренд: Enterasys Страницы: 62

Бренд: Ciara Страницы: 14

Бренд: Supero Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды