Cisco ASR 9000 Series Скачать руководство пользователя

Страница: 63 / 1138

pm otn threshold

To configure performance monitoring thresholds on the optical transport network (OTN) layer, use the

otn threshold

command in DWDM configuration mode. To disable TCA reporting, use the

form of this

command.

{

15-min| 24-hour

}

otn threshold otn-paramter enable

no pm

{

15-min| 24-hour

}

otn threshold otn-paramter enable

Syntax Description

Configures performance monitoring thresholds for 15-minute intervals.

15-min

Configures performance monitoring thresholds for 24-hour intervals.

24-hour

Specific parameter for which to configure the threshold. OTN parameters can be as follows:

•

bbe-pm-fe

—

Far-end path monitoring background block errors (BBE-PM). Indicates

the number of background block errors recorded in the optical transport network (OTN)
path during the performance monitoring time interval.

•

bbe-pm-ne

—

Near-end path monitoring background block errors (BBE-PM).

•

bbe-sm-fe

—

Far-end section monitoring background block errors (BBE-SM). Indicates

the number of background block errors recorded in the OTN section during the
performance monitoring time interval.

•

bbe-sm-ne

—

Near-end section monitoring background block errors (BBE-SM).

•

bber-pm-fe

—

Far-end path monitoring background block errors ratio (BBER-PM).

Indicates the background block errors ratio recorded in the OTN path during the
performance monitoring time interval.

•

bber-pm-ne

—

Near-end path monitoring background block errors ratio (BBER-PM).

•

bber-sm-fe

—

Far-end section monitoring background block errors ratio (BBER-SM).

Indicates the background block errors ratio recorded in the OTN section during the
performance monitoring time interval.

•

bber-sm-ne

—

Near-end section monitoring background block errors ratio (BBER-SM)

•

es-pm-fe

—

Far-end path monitoring errored seconds (ES-PM). Indicates the errored

seconds recorded in the OTN path during the performance monitoring time interval.

•

es-pm-ne

—

Near-end path monitoring errored seconds (ES-PM).

•

es-sm-fe

—

Far-end section monitoring errored seconds (ES-SM). Indicates the errored

seconds recorded in the OTN section during the performance monitoring time interval.

•

es-sm-ne

—

Near-end section monitoring errored seconds (ES-SM).

otn-parameter

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

Dense Wavelength Division Multiplexing Commands on the Cisco ASR 9000 Series Router

pm otn threshold

Содержание ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ASR 9000 Series

Отзывы:

Похожие инструкции для ASR 9000 Series

Бренды по названию

Популярные бренды

Cisco ASR 9000 Series, Справочник по командам

Результаты поиска

Содержание ASR 9000 Series

Отзывы:

Похожие инструкции для ASR 9000 Series

Бренды по названию

Популярные бренды