Cisco ASR 14000 Series Скачать руководство пользователя страница 117

Страница: 117 / 132

5-5

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

OL-16973-01

Chapter 5 Installing and Removing Exterior Components

Installing or Removing the Front Side Exterior Components

Figure 5-3

Inlet Grille

Prerequisites

Before installing the inlet grille, you should mount the chassis in a rack and remove the rear handle pulls.
See

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Unpacking, Moving, and Securing Guide

Required Tools and Equipment

•

ESD-preventive wrist strap

•

Inlet grille (Cisco product number: ASR14K-8-FRNT-GRILL=)

•

Number 1 Phillips screwdriver

•

Left AC rectifier power handle (Cisco product number: FABMTL,EXTENSION,PWR,L,HQ,HFR)

•

Right AC rectifier power handle (Cisco product number: FABMTL,EXTENSION,PWR,R,HQ,HFR)

Steps

To install the inlet grille, follow these steps:

Step 1

Remove the new inlet grille from its packaging, then set the packaging aside.

Step 2

Remove the AC rectifier power handles from their package.

Step 3

Attach the ESD-preventive wrist strap to your wrist and connect its leash to one of the ESD connection
sockets on the front (PLIM) side of the chassis or a bare metal surface on the chassis.

Step 4

If the old inlet grille is installed, remove the old inlet grille (see the next section, “

Removing the Inlet

Grille

”).

210878

I/LIM

C O

CB/TRIP IN/F

AIL

PWR/OK

I/LIM

C O

/TRIP

IN/F

AIL

R/OK

Содержание ASR 14000 Series





































































































































Результаты поиска

Содержание ASR 14000 Series

Отзывы:

Cisco ASR 14000 Series, Руководство по установке, Страница: 117 / 132

Результаты поиска

Содержание ASR 14000 Series

Отзывы: