Cisco Aironet 1530 Series, 1532 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 69

background image

2-28

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Chapter 2 Installing the Access Point

Installing Antennas

Step 1

Position and slide the cover over the AP as shown in

.

Step 2

Align the two holes on each side of the cover with the screw holes on corresponding side of the AP.

Step 3

Insert and install #8-32 screws through the screw holes in the cover and into the AP. Tighten the screws
to 10 lb-in.

Installing Antennas

shows the antennas supported by the 1532 access point and provides required quantities for

each model.

For installation instructions and detailed information on these antennas, refer to the appropriate
document located at:

http://www.cisco.com/en/US/products/hw/wireless/ps469/prod_installation_guides_list.html

Follow all safety precautions when installing the antennas. For information on safety, refer to

Precautions when Installing Antennas” section on page 2-29

Non-Cisco Antennas

Cisco does not support any third-party antennas. RF connectivity and compliance of third party antennas
is the customer’s responsibility. Cisco does not recommend any third-party antennas, and Cisco
Technical Assistance Center will not be able to provide any support for third-party antennas. Cisco’s
FCC Part 15 compliance is only guaranteed with Cisco antennas or antennas that are of the same design
and gain as Cisco antennas.

Table 2-6

1532 Access Point Supported External Antennas

Product ID

Frequency
Band

Gain

Type

AIR-ANT2547VG-N

2.4 / 5 GHz

4 / 7 dBi

Omnidirectional (gray)

AIR-ANT2547V-N

2.4 / 5 GHz

4 / 7 dBi

Omnidirectional (white)

AIR-ANT2588P3M-N=

2.4 / 5 GHz

4 / 7 dBi

Omnidirectional

AIR-ANT2588P3M-N

2.4 / 5 GHz

8 / 8 dBi

Directional

AIR-ANT2450V-N

2.4 GHz

5 dBi

Omnidirectional

AIR-ANT2480V-N

2.4 GHz

8 dBi

Omnidirectional

AIR-ANT2413P2M-N=

2.4 GHz

13 dBi

Directional

AIR-ANT5180V-N

5 GHz

8 dBi

Omnidirectional

AIR-ANT5114P2M-N=

5 GHz

14 dBi

Directional

«
...
58
59
60
61
62
...
»

Содержание Aironet 1530 Series, 1532






































































Отзывы:

Нет отзывов

Похожие инструкции для Aironet 1530 Series, 1532

Бренд: D-Link Страницы: 166

Бренд: D-Link Страницы: 147

Бренд: Arris Страницы: 2

EWP-WA6630X-JP-FIT

Бренд: H3C Страницы: 34

Бренд: ZyXEL Communications Страницы: 11

ZoneFlex series

Бренд: Ruckus Wireless Страницы: 68

Бренд: Abocom Страницы: 12

AIR-CAP3501E-A-K9

Бренд: Cisco Страницы: 34

AIR-AP1210 - Aironet 1200 - Wireless Access Point External

Бренд: Cisco Страницы: 35

Aironet 1520 Series

Бренд: Cisco Страницы: 66

Бренд: Cisco Страницы: 44

AIR-CAP1552H-x-K9

Бренд: Cisco Страницы: 24

AIR-AP1542D-*-K9

Бренд: Cisco Страницы: 72

AIR-AP1010 - 1000 Series Lightweight Access Point

Бренд: Cisco Страницы: 36

AIR-BR1310G-A-K9 - Aironet 1310 Outdoor Access Point/Bridge

Бренд: Cisco Страницы: 14

AIR-AP1232AG-A-K9 - Aironet 1230AG - Wireless Access Point

Бренд: Cisco Страницы: 8

1231G - Aironet - Wireless Access Point

Бренд: Cisco Страницы: 126

AIR-AP1251AG-A-k9

Бренд: Cisco Страницы: 140

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды