Cisco aironet 1130 Скачать руководство пользователя страница 104

Страница: 104 / 184

104

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Connecting the Cisco 1520 Series Mesh Access Point to Your Network

Figure 67

VLAN Access Mode

If configuring a RAP or MAP

trunk

port, click

gigabitEthernet0

(port 0-PoE in).

Select

trunk

from the mode drop-down menu. (See

Figure 68

Enter a native VLAN ID for

incoming

traffic. The native VLAN ID can be any value between 1

and 4095. Do not assign any value assigned to a user-VLAN (access).

Click

Apply

A trunk VLAN ID field and a summary of configured VLANs appears at the bottom of the
screen. The trunk VLAN ID field is for outgoing packets.

Enter a trunk VLAN ID for

outgoing

packets:

If forwarding

untagged

packets, do not change the default trunk VLAN ID value of zero.

(MAP-to-MAP bridging, campus environment)

If forwarding

tagged

packets, enter a VLAN ID (1 to 4095) that is not already assigned. (RAP

to switch on wired network).

Click

Add

to add the trunk VLAN ID to the allowed VLAN list.

The newly added VLAN

displays under the Configured VLANs section on the window.

Note

To remove a VLAN from the list, select the Remove option from the arrow drop-down
to the right of the desired VLAN.

Figure 68

All APs > AP > VLAN Mappings Window

Step 5

Click

Apply

Step 6

Click

Save

Configuration

to save your changes.

Содержание aironet 1130

























































































































































































Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды

Cisco aironet 1130, Руководство по проектированию и развертыванию

Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды