manualshive.com logo in svg

Cisco 910, Руководство по установке, Страница: 15 / 18

Поделиться
Скачать
Cisco 910 Скачать руководство пользователя страница 15

33

   

Cisco 910 Industrial Router Installation

Installing and Removing the SSD Storage Card

4.

Tighten each screw inside the bore to fix the sensor card to the carrier.

Installing the Sensor Card Module into the Router

Follow these steps to install the sensor card into the open slot in the Cisco 910 Industrial Router:

1.

Before you install (or remove) the sensor card from the router, power down the router first.

2.

Insert the sensor card into the open slot.

3.

Using a screwdriver, secure the two captive screws into place.

Removing the Sensor Card Module From the Router

Follow these steps to remove the sensor card from the open slot in the Cisco 910 Industrial Router:

1.

Using a screwdriver, loosen the two captive screws on the open slot sensor card carrier.

2.

Gently pull the sensor card out of the open slot.

Installing and Removing the SSD Storage Card

This section describes the installation and removal of the SSD storage card. 

Figure 6

 shows an SSD storage card assembled into the SSD carrier.

Figure 6

SSD Card Module

If you have ordered the SSD storage card together with your chassis, it will be preinstalled into the router. 

392065

Содержание 910



















Отзывы:

Нет отзывов