background image

 

vii

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Preface

This preface describes the objectives, audience, organization, and conventions of this guide, and 
describes related documents that have additional information. It contains the following sections:

  •

Objectives, page vii

  •

Audience, page vii

  •

Organization, page viii

  •

Conventions, page viii

  •

Searching for Cisco Documents, page xiv

  •

Obtaining Documentation and Submitting a Service Request, page xv

Objectives

This guide provides an overview and explains how to install, connect, and perform initial configuration 
for the Cisco Connected Grid Routers (CGR) 2010.

For warranty, service, and support information, see the “Cisco Warranty Terms” section in the 

Readme 

First

 for the Cisco 2010 CGR document that was shipped with your router.

Audience

This documentation is designed for the person installing, configuring, and maintaining the router, who 
should be familiar with electronic circuitry and wiring practices and has experience as an electronic or 
electromechanical technician. It identifies certain procedures that should be performed only by trained 
and qualified personnel. 

Содержание 2010





























































































Отзывы: