Cisco 10008 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 70

Cisco 10008 Скачать руководство пользователя страница 8

8

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

Software Compatibility

Safety Warnings

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may
harm you. A warning symbol precedes each warning statement. The following warning is an example of
a safety warning. It identifies the warning symbol and associates it with a bodily injury hazard.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Note

If you need translations of the safety warning, see the

Regulatory Compliance and Safety Information

for Cisco 10000 Series Routers

Software Compatibility

The PRE4 has specific Cisco IOS software requirements.

shows the minimum required Cisco

IOS software for the PRE4.

Use the

show version

command to display the system software version that is currently loaded and

running.

If the output of the

show version

command indicates that the Cisco IOS software is a version earlier than

the version identified as the minimum Cisco IOS software release in

, check the contents of the

CompactFlash memory to determine if the required images are available on your system.

The output of the

show flash

command provides a list of all files stored in the CompactFlash memory.

If the correct software version is not installed, contact Cisco Customer Service (see the

Documentation, Obtaining Support, and Security Guidelines” section on page 68

Installation Guidelines

This section contains guidelines for the following:

•

A new installation

•

A replacement installation

•

The required tools and equipment

Table 4

PRE4 Software Compatibility

PRE4 Product Number

Cisco IOS Release

Minimum Cisco IOS Release

ESR-PRE4

12.2(33)SB

12.2(33)SB

«
...
6
7
8
9
10
...
»

Содержание 10008







































































Отзывы:

Нет отзывов