Cisco 10008 Скачать руководство пользователя страница 47

Страница: 47 / 70

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

TCAM Commands

tunnel lookup = 0 0

tunnel RX = 0 0

tunnel TX = 0 0

output qos = 0 0

tag not ip = 0 0

netflow accumulate = 0 0

netflow age = 0 0

netflow swap = 0 0

IPv6 Forwarding over MPLS

The Cisco 10008 router supports PXF–accelerated IPv6 packet forwarding over Multiprotocol Label
Switching (MPLS) on the PRE4. This feature is enabled by default.

Table 9

lists common IPv6 commands. For more information about IPv6 commands, refer to the Cisco

IOS Command Reference publication for your Cisco IOS software release.

TCAM Commands

This section describes the following commands for ACL lookup using the Ternary Content Addressable
Memory (TCAM) on the PRE4:

•

hw-module tcam, page 48

•

show pxf cpu access-lists, page 50

•

show pxf cpu pbr action, page 56

•

show pxf cpu qos, page 60

•

show pxf dma, page 62

•

show pxf tcam, page 65

Table 9

IPv6 Forwarding over MPLS Commands

Command Purpose

Router(config)#

ipv6 access-list

Configures an IPv6 access list and places the
router in IPv6 access list configuration mode.

Router(config)#

ipv6 cef

Enables Cisco Express Forwarding for IPv6
(CEFv6).

Router(config)#

ipv6 cef distributed

Enables distributed CEFv6 (dCEFv6) to
process IPv6 packets from the Route
Processor (RP) to the line cards.

Router(config)#

ipv6 unicast-routing

Enables the forwarding of IPv6 packets.

Router(config-if)#

ipv6 enable

Enables IPv6 processing on an interface that
has not been configured with an explicit IPv6
address.

Router(config-if)#

ipv6 address

Configures an IPv6 address based on an IPv6
general prefix and enables IPv6 processing on
an interface,

Router#

show pxf cpu ipv6

Displays PXF IPv6 statistics.

Содержание 10008







































































Результаты поиска

Содержание 10008

Отзывы:

Cisco 10008, Руководство по установке и настройке, Страница: 47 / 70

Результаты поиска

Содержание 10008

Отзывы: