manualshive.com logo in svg

CIS VISION:mini VCC-G21X31ACL, Техническое описание и руководство по эксплуатации

Поделиться
Скачать
CIS VISION:mini VCC-G21X31ACL Скачать руководство пользователя страница 5

VCC-G21X31ACL  

Rev.900-711-32-00

 

©2011 CIS Corporation. All rights reserved. 

 

5

3.  Product Outline 

VCC-G21X31ACL is a high-resolution industrial B/W digital video camera module utilizing a 1/3 type PS IT CCD.   
800K pixels CCD image sensor with on-chip micro-lenses realizes high sensitivity and high resolution. 
At Full Frame Scan Mode, entire pixels can be read out within approx. 1/36s.    Interface of G21X31ACL complies 
with camera link standard. 
 
Key Features 

□ 

Camera settings can be changed via serial communications. 

□ 

Selectable 8 bit or 10 bit. 

□ 

1/36

～

1/48,000s shutter speeds can be set per 1H. 

□ 

Full frame scan mode and three different partial scan modes are available. 

□ 

Four different binning scan modes are available. 

□ 

Approx. 36 fps at full frame scan mode. 

□ 

Only 29mm cubic in size (excluding projection), light weight 50g, and speed makes it a best match for   

 

use in embedded systems. 

 

Содержание VISION:mini VCC-G21X31ACL





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды