Cirrus Logic CS4953xx Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 118

background image

DAI Hardware Configuration

CS4953xx Hardware Users Manual

DS732UM7

Copyright 2008 Cirrus Logic, Inc

5-4

5.1.4 Digital Audio Formats

The DAI has 5 stereo data input pins that are fully configurable including support for I

2

S, and left-justified formats.

DAI ports are programmed for slave operation, where DAIn_LRCLK and DAIn_SCLK are inputs only. This
subsection describes some common audio formats that CS4953xx supports. It should be noted that the input ports
use up to 32-bit PCM resolution and 16-bit compressed data word lengths.

5.1.4.1 I

2

S Format

illustrates the I

2

S format. For I

2

S, data is presented most-significant bit (MSB) first, one SCLK delay

after the transition of DAIn_LRCLK, and is valid on the rising edge of DAIn_SCLK. For the I

2

S format, the left

subframe is presented when DAIn_LRCLK is low, and the right subframe is presented when DAIn_LRCLK is high.

Figure 5-2. I2S format (Rising Edge Valid SCLK)

5.1.4.2 Left-Justified Format

illustrates the left-justified format with a rising-edge DAIn_SCLK. Data is presented most-significant bit

first on the first DAIn_SCLK after a DAIn_LRCLK transition and is valid on the rising edge of DAIn_SCLK. For
the left-justified format, the left subframe is presented when DAIn_LRCLK is high and the right subframe is
presented when DAIn_LRCLK is low. The left-justified format can also be programmed for data to be valid on the
falling edge of DAIn_SCLK.

Figure 5-3. Left-justified Format (Rising Edge Valid SCLK)

5.2 DAI Hardware Configuration

After code download or soft reset, and before kickstarting the application, the host has the option of changing the
default hardware configuration. (Please see AN288, “CS4953xx Firmware User’s Manual” for more information on
kickstarting). In general, the hardware configuration can only be changed immediately after download or after soft
reset.

Hardware configuration messages are used to physically reconfigure the hardware of the audio decoder, as when
enabling or disabling address checking for the serial communication port. Hardware configuration messages are also

DAO_LRCLK

DAO_SCLK

Left Channel

Right Channel

DAO_DATA

+3 +2 +1 LSB

+5 +4

MSB-1 -2 -3 -4 -5

+3 +2 +1 LSB

+5 +4

MSB-1 -2 -3 -4

DAIn_LRCLK

DAIn_SCLK

L e ft C h a n n e l

R i g ht C h a n n el

DAIn_DATA

+3

+2

+1

LSB

+5

+4

MSB

-1

-2

-3

-4

-5

+3

+2

+1

+5

+4

-1

-2

-3

-4

LSB

MSB

«
...
60
61
62
63
64
...
»

Содержание CS4953xx























































































































Отзывы:

Нет отзывов

Похожие инструкции для CS4953xx

MediaLounge DSM-520

Бренд: D-Link Страницы: 127

DivX Connected DSM-330

Бренд: D-Link Страницы: 38

AZZUPRO 5-20-ZSS

Бренд: ZCS Страницы: 44

Бренд: Magnimage Страницы: 40

Бренд: Mase Страницы: 22

Бренд: Kramer Страницы: 15

Бренд: PEAK COMMUNICATIONS Страницы: 18

Бренд: ADF Web Страницы: 25

Бренд: Kramer Страницы: 30

ATLONA AT-HDVS-RX

Бренд: Panduit Страницы: 2

Sunny Island 3324

Бренд: SMA Страницы: 80

OPS500-501 Series

Бренд: AXIOMTEK Страницы: 54

Бренд: Actox Страницы: 36

Бренд: Systech Corporation Страницы: 6

Бренд: Fronius Страницы: 92

Бренд: Altera Страницы: 87

Бренд: CTC Union Страницы: 44

HDMI Encoder 8x

Бренд: NetUP Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды