Cirrus Logic CS44600 Скачать руководство пользователя | Manualshive

Страница: 42 / 76

background image

42

DS633F1

CS44600

6. When driving a single-ended (half-bridged) power output stage, set the RAMP[1:0] bits to ‘11’b and

the required ramp speed, to initiate a ramp cycle when the channel is powered on. Set
MIN_PULSE[4:0] to ‘00000’b.

7. Set the PDN bit to ‘0’b to take the CS44600 out of the power-down state.

8. Start all clocks on the DAI interface (DAI_MCLK, DAI_SCLK, DAI_LRCK). This will initiate the SRC to

begin the lock sequence. The SRC lock function can be configured to cause an interrupt condition
when lock has been completed. This will be indicated by an active INT signal.

9. Wait for the SRC to lock.

10. If using the PSR feedback, jump to

“Recommended PSR Calibration Sequence” on page 44

. When

finished, continue to step 12. If not using PSR feedback, continue to step 12.

11. Set the appropriate GPIO pin, or other control signal, to enable the power output stage.

12. Enable each channel’s PWM modulator by setting the PDN_PWMxx bit to ‘0’b. If full-bridged, go to

step 14. If single-ended (half-bridged), this will initiate a sequence which will slowly increase the DC
voltage, from 0V to Vpower÷2, across the AC coupling capacitor. This will eliminate the instantaneous
charge across the capacitor which would have caused an audible pop from the speaker.

13. Wait for the ramp-up sequence to complete. The ramp-up function can be configured to cause an

interrupt condition when the ramp period has completed. This will be indicated by an active INT signal.
Once the ramp-up sequence has completed, set the RAMP[1:0] bits to ‘01’b

14. For full-bridged power output stage configurations, the ramp-up sequence is not required. Enabling

the power output stage will not cause an audible pop from the speaker.

15. If using the PSR feedback, set the FEEDBACK_EN bit to ‘1’b.

16. Un-mute all active channels.

17. At this point, the CS44600 is ready to accept audio samples and begin playback.

5.1.3

Recommended PSR Calibration Sequence

1. Set the DEC_SHIFT[2:0]/DEC_SCALE[18:0] coefficient (C

PSR

) to decimal 1.0 (register 35h = 22h,

36h = 00h, 37h = 00h).

2. Set the PSR_RESET bit to ‘1’b.

3. Set the PSR_EN bit to ‘1’b.

4. Set the PSR_EN bit to ‘0’b.

5. Read DEC_OUTD[23:0].

6. See

to adjust the DEC_SHIFT[2:0]/DEC_SCALE[18:0] registers.

7. Continue Recommended Power-Up Sequence.

«
...
40
41
42
43
44
...
»

Содержание CS44600













































































Отзывы:

Нет отзывов

Похожие инструкции для CS44600

Бренд: Ubisys Страницы: 2

Бренд: Maestra Страницы: 22

Бренд: S&P Страницы: 17

Бренд: S&S Northern Страницы: 9

Бренд: Balboa Страницы: 23

Бренд: Balboa Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Eaton Страницы: 448

Бренд: Eaton Страницы: 57

Бренд: Coccolle Страницы: 11

Бренд: Centurion Страницы: 16

Бренд: Samson Страницы: 70

Бренд: Keysight Technologies Страницы: 105

Бренд: Barco Страницы: 4

Бренд: Velleman Страницы: 22

Бренд: National Instruments Страницы: 27

MU System X Dual Amplifier

Бренд: Frequency Central Страницы: 4

Бренд: Sysmac Страницы: 159

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды