Cirrus Logic CS44600 Скачать руководство пользователя | Manualshive

Страница: 22 / 76

background image

22

DS633F1

CS44600

4. APPLICATIONS

4.1

Overview

The CS44600 is a multi-channel digital-to-PWM Class D audio system controller including interpolation,
sample rate conversion, half- and full-bridge PWM driver outputs, and power supply rejection feedback in a
64-pin LQFP package. The architecture uses a direct-to-digital approach that maintains digital signal integ-
rity to the final output filter, minimizing analog interference effects which negatively affect system perfor-
mance.

The CS44600 integrates on-chip sample rate conversion, digital volume control, peak detect with volume
limiter, de-emphasis, programmable interrupt conditions, and the ability to change the PWM switch rate to
eliminate AM frequency interference. The CS44600 also has a programmable load compensation filter,
which allows the speaker load to vary while the output filter remains fixed, maintaining a flat frequency re-
sponse. For single-ended half-bridge applications PWM Popguard

®

reduces the transient pops and clicks

and realtime power supply feedback reduces noise coupling from the power supply. The PWM amplifier can
achieve greater than 90% efficiency. This efficiency provides for a smaller device package, less heat sink
requirements, and smaller power supplies.

The CS44600 is ideal for audio systems requiring wide dynamic range, negligible distortion, and low noise
such as A/V receivers, DVD receivers, digital speaker, and automotive audio systems.

4.2

Feature Set Summary

Core Features

•

2.5 V digital core voltage, VD.

•

VLC voltage pin for host interface logic levels between 2.5 V and 5.0 V.

•

VLS voltage pin for digital audio interface logic levels between 2.5 V and 5.0 V.

•

VDP voltage pin for PWM backend interface logic levels between 3.3 V and 5.0 V.

•

VDX voltage pin for clock input signals between 2.5 V and 5.0 V.

Clocking

•

Minimum of 128Fs DAI_MCLK for DAI serial interface.

•

DAI interface uses automatic detection of LRCK/MCLK ratio to configure internal DAI/SRC clocks.

•

All PWM Processing clocks generated internally via:

–

An external crystal - 24.576 MHz to 54 MHz, or

–

XTI input pin capable of supporting a clock signal at the VDX voltage level.

•

Programmable divide of XTI by 1, 2, 4, 8 for SYS_CLK output.

•

Programmable divide of XTI by 32, 64, 128, 256 for PS_SYNC (power supply synchronization signal).

Digital Audio Playback

•

Supports 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz sample frequencies.

•

High performance sample rate converter.

•

16, 20 and 24 bit audio sample lengths.

•

De-emphasis for 32 kHz, 44.1 kHz, 48 kHz.

«
...
20
21
22
23
24
...
»

Содержание CS44600













































































Отзывы:

Нет отзывов

Похожие инструкции для CS44600

Бренд: IBM Страницы: 105

ecomat 100 R 360

Бренд: IFM Electronic Страницы: 16

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 11

Бренд: IFM Electronic Страницы: 23

SIGMA CONTROL 2

Бренд: KAESER KOMPRESSOREN Страницы: 246

Бренд: Water Specialist Страницы: 60

Бренд: Eaton Страницы: 96

Бренд: J+J Страницы: 4

Бренд: Val Controls Страницы: 6

Бренд: Panasonic Страницы: 8

Бренд: Maximum Controls Страницы: 58

Бренд: Nemesis Страницы: 6

Бренд: Sven Страницы: 6

Бренд: Binder Страницы: 147

Бренд: Netro Страницы: 14

Бренд: knorr-baby Страницы: 44

Бренд: ICP DAS USA Страницы: 6

SMARC conga-SMX8-X

Бренд: Congatec Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды