Cirrus Logic CDB48500-USB Скачать руководство пользователя страница 13

Страница: 13 / 52

2-3

DS784DB1

Introduction
CDB48500-USB Evaluation Kit Guide

2.1.2 Setting up the Evaluation Kit Boards

Figure 2-2. Board Setup Diagram

Place the CDB48500 and the CDB USB MASTER on a static-free surface.

2. If the boards are not mated, connect them together as shown in

Figure 2-2

. Notice that the USB

connector on the CDB USB MASTER and the power connector on the CDB48500 are on the same
side.

3. Connect the Power Supply as follows:

A. Connect the power supply jack to the CDB48500 board at J25 and the adapter to a wall power

socket or power strip.

B. Check that the D3 (green, 3.3V), D2 (red, 1.8V), and D4 (orange, 5V) power indicator LEDs

illuminate on the CDB48500.

4. Setup Audio Input connections to the CDB48500 as follows:

A. Connect one end of the digital audio S/PDIF optical cable to SPDIF_RXP on the CDB48500

board.

B. Connect the other end of the optical cable to the optical output on the back of a DVD player or

other digital audio source.

5. Setup Audio Output connections from CDB48500 as follows:

A. The RCA connectors labeled AOUT_1A and AOUT_1B are the left and right analog output

channels.

PDIF_

RXP

CS48560

U
S
B

AIN_6B

USB

Cable

Power

Cable

RCA Cables

To Powered

Speakers

Optical

Cable

Analog

Inputs

SPDIF_RXIN

Optical

Output

Optical Output on

DVD Player

Cirr

us L

ftw

are

USB 2.0

Port

SPDIF_

“A”

“B”

Analog

Outputs

HP_OUT

AIN_5A

AIN_4A

AIN_3A

AIN_2A

AIN_1A

AIN_6A

AIN_5B

AIN_4B

AIN_3B

AIN_2B

AIN_1B

AOU

T_1A

AOU

T_2A

AOU

T_3A

AOU

T_4A

AOU

T_5A

AOU

T_6A

UT_1B

UT_2B

UT_3B

UT_4B

UT_5B

UT_6B

C_I

DVD P

layer

CDB48560

UNUSED

HP_OUT

AIN_4A

UNUSED

AIN_3A

AIN_2A

AIN_1A

UNUSED

AIN_4B

UNUSED

AIN_3B

AIN_2B

AIN_1B

AOU

UNUSED

AOU

UNUSE

NUSED

C_IN

CDB48540

UNUSED

HP_OUT

AIN_2A

UNUSED

AIN_1A

UNUSED

AIN_2B

UNUSED

AIN_1B

AOU

T_1A

NUSED

AOU

T_2A

AOUT_1B

UNUSED

AOUT_2B

UNUSED

MIC_

CDB48520

Содержание CDB48500-USB






































Результаты поиска

Содержание CDB48500-USB

Отзывы:

Cirrus Logic CDB48500-USB, Руководство пользователя, Страница: 13 / 52

Результаты поиска

Содержание CDB48500-USB

Отзывы: