background image

READ THIS ENTIRE PAGE BEFORE PROCEEDING 

 
FOR SAFETY OF PERSONNEL AND TO PREVENT DAMAGE TO EQUIPMENT, FOLLOWING 
NOMENCLATURE HAS BEEN USED IN THIS MANUAL: 
 

 

DANGER

 

 

Failure to observe precautions noted in this box can result in severe bodily injury 
or loss of life. 

 

 

WARNING

 

 

Failure to observe precautions noted in this box can cause injury to personnel by 
accidental contact with the equipment or liquids.  Protection should be provided by 
user to prevent accidental contact. 

 

 

CAUTION

 

 

ATTENTION

 

 

Failure to observe precautions noted in this box can cause damage or failure of 
the equipment. 

 

Non compliance of safety 
instructions identified by 
following symbol could 
affect safety for persons: 

Safety instructions where 
electrical safety is 
involved are identified by: 

Safety instructions which 
shall be considered for 
reasons of safe operation 
of the pump and/or 
protection of pump itself 
are marked by sign: 

 

 

ATTENTION 

 

 

ATTENTION

If operation of pump is critical to your business, we strongly recommend you keep 
a spare pump or major repair kit in stock at all times.  As a minimum, a minor 
repair kit (o-rings, gaskets, shaft seal and bearings) should be kept in stock so 
pump refurbishment after internal inspection can be accomplished. 

 

CONTENTS 

 
Safety and Table of Contents ....................................................................................................... A 
General  Instructions ..................................................................................................................... 1 
Introduction ................................................................................................................................... 1 
Ordering Instructions .................................................................................................................... 1 
Description of the Equipment ........................................................................................................ 1 
Pump Model Identification ............................................................................................................ 2 
Operation ...................................................................................................................................... 2 
Parts List ....................................................................................................................................... 3 
Assembly and Disassembly Instructions ................................................................................... 3-5 
Troubleshooting and Field and Factory Service and Parts ........................................................... 6 
Assembly Drawings ...................................................................................................................... 7 
 

Содержание IMO G323FHF Series











Отзывы: