CIRCLE M6 DC Скачать руководство пользователя страница 12

Страница: 12 / 22

Document: Service Manual

Description: Treadmill

Model: M6 DC

Approved Date: 2017.05.09

Page: 12 of 22

4. ENGINEERING MODE

4.1 How to enter the Engineering Mode

1. In IDEL mode, hold on Stop/Reset key and then press SPEED Increase key to enter the Engineering
Mode.
2. Press Enter key to skip to next setting and then back to IDEL mode, the sequences are below:

4.2 Function Descriptions of Engineering Mode

(1) Software version information:

Incline window shows display page, Time window shows display information. Press SPEED key or

Incline

key to change the display pages as following:

- Software version
- The year of Software date
- The month of Software date
- The day of Software date
Press Enter key to skip to next setting.

(2) Unit setting:

Message window shows

『

UNIT - METRIC

』

, press SPEED key or Incline key to change to

『

UNIT -

ENGLISH

』

, press Enter key to confirm and skip to next setting.

(3) Roller size setting:

- Message window shows

『

ROLLER = XX.X

』

press SPEED key to change the roller size.

- Press Enter key to confirm and skip to next setting.

(4) Motor stop manner:

- Message window shows

『

MOTOR CONTROL

』

, press SPEED key to change to

『

MOTOR FREE

』

- Press Enter key to confirm and skip to next setting.
* MOTOR CONTROL:

means to slow down to lowest speed by motor control while stop.

* MOTOR FREE:

means to cut off the motor power while stop.

(5) Min. speed setting:

Message window shows

『

MIN SPEED X.X

』

, press SPEED key to set the min. Speed.

- Press Enter key to confirm and skip to next setting.

Содержание M6 DC























Результаты поиска

Содержание M6 DC

Отзывы:

Бренды по названию

Популярные бренды

CIRCLE M6 DC, Руководство по обслуживанию

Результаты поиска

Содержание M6 DC

Отзывы:

Бренды по названию

Популярные бренды