Cincinnati Sub-Zero NORM-O-TEMP Скачать руководство пользователя страница 4

Operation Manual

                                

   

NORM-O-TEMP, Model 111W

  

 
 

Page 4 of 26 

Cincinnati Sub-Zero Products, Inc., reserves the right to make changes to the device, which may not be 
reflected in this manual. 

WARNING 

 

A physician's order is required for the use of the device and setting the temperature of the 

blanket/pad. At least every 20 minutes, or as directed by physician, check patient's temperature 
and skin condition of areas in contact with blanket/pad; also, check blanket/pad water 

temperature. Pediatric patients, temperature-sensitive patients with vascular disease, surgical 
patients, diabetic and Reynaud’s disease patients should be checked more frequently.  If patient’s 

temperature does not reach desired set point or differs drastically from recommended set point, 
notify physician. 

Notify the physician promptly of any change in patient status in order to 

avoid serious injury or death.

  

1.

 

Pediatrics – Infant’s and children’s body temperatures are often more responsive to 
surface heating and cooling than adults.  Due to their size, the effect of heating or 
cooling a child is likely more pronounced because of their higher ratio of skin contact 

area to body mass. 

2.

 

Temperature Sensitive Patients – Patients with impaired peripheral blood circulation 
and patients who are incapacitated may be more sensitive to temperature changes 

than patients with normal circulation. 

3.

 

Surgical Patients – Patients with poor circulation due to inadequate heart function, loss 
of blood, or impaired peripheral blood circulation may be more sensitive to 

temperature changes. 

 

The method of temperature control provided by all hyperthermia units presents the danger of 

heating body tissues, particularly the skin, to a point where they are injured. Depending on the 
extent and severity of a burn, 

very serious and even fatal complications may arise.  

 

 

Do not use the NORM-O-TEMP

®

 System distal to arterial cross clamping. 

Thermal injury may 

result.

 

 

Prevent excessive and/or prolonged tissue pressure and shearing forces, especially over bony 

prominences, to prevent 

skin damage that may result.

 

 

Do not place additional heat sources between the patient and blanket/pad. 

Skin damage may 

result.

 

 

The area between the patient and the blanket/pad should be kept dry to avoid injury to 

patient. 

 Prep solutions have been reported to injure the skin when allowed to remain between 

patients and a water-circulating heating blanket/pad during prolonged procedures.  

 

Proper sanitation procedures must be practiced and hygienic safety must be maintained, 
to prevent contamination.

  Contamination can affect patient’s health, i.e. skin irritation/rash 

may result.

 

 

Do not use the NORM-O-TEMP

®

 system in the presence of flammable anesthetics. 

Risk of 

explosion can result.

 

 

Power interruption will cause the NORM-O-TEMP

®

 unit to revert to Preset Set point Temperature 

resulting  in  possible  inaccurate  therapy  to  the  patient.  Follow  instructions  for  First  Time  Set-

Up/System  Test  Routine  located  in  the  Operation/Technical  Manual  to  resume  operation.  

Failure to resume therapy could result in serious injury or death. 

 

Do  not by-pass ground lug.

   Electrical Hazards may result.

 

 

Any time water is found leaking into or around the unit, connecting hose, and/or blanket/pad, 

turn the unit off, disconnect the power cord from its power source, and correct the problem 
before  proceeding.

  Water  leaks  could  lead  to  electric  shock.    Water  leaks  could  also 

present a slip hazard.  

 

Содержание NORM-O-TEMP





























Отзывы: